Journal of Advanced Materials and Technologies

Journal of Advanced Materials and Technologies

The Effects of Energy Density on the Density and Microstructure of 316L Stainless Steel Produced by Selective Laser Melting

Document Type : Original Reaearch Article

Authors
Mohammadamin Bakhtiarian 1
Alborz Fathi Younesi 2
Hamid Omidvar 3, 4
1 MSc, Department of Materials and Metallurgical Engineering, Amirkabir University of Technology, Tehran, P. O. Box: 1599637111, Iran.
2 Master of Material Science and Engineering, University of Tehran, Tehran, Iran.
3 Associate Professor, Department of Materials and Metallurgical Engineering, Amirkabir University of Technology, Tehran, P. O. Box: 1599637111, Iran.
4 Center for International Scientific Studies and Collaborations (CISSC) of Iran, Tehran, Iran
10.30501/jamt.2024.451706.1299
Abstract
The selective laser melting process is one of the additive manufacturing processes of metals in which a laser beam melts selected areas on a powder bed and creates the parts in layers. One of the important challenges of this method is to make a part without any defects and reaching 100% density. The material selected for this study is stainless steel 316L powder and the NOURA M100P machine was used to make the samples. In this research, six samples with different energy densities were made from 160 j/mm3 to 260 j/mm3. After making the samples, their density was measured by the Archimedes method. A sample made with an energy density of 220 j/mm3 has the highest relative density of 97.93. By examining the microstructure of the printed samples, it was determined that the samples have grain boundary cracks and incomplete fusion cavities and keyhole phenomenon.
Keywords
Stainless Steel 316L
Selective Laser Melting
Energy Density
Relative Density
Microstructure

Subjects

  1. Bakhtiarian, M., Omidvar, H., Mashhuriazar, A., Sajuri, Z., & Gur, C. H. (2024). The effects of SLM process parameters on the relative density and hardness of austenitic stainless steel 316L. Journal of Materials Research and Technology, 29, 1616–29. https://doi.org/https://doi.org/10.1016/j.jmrt.2024.01.237
  2. Bang, G. B., Kim, W. R., Kim, H. K., Park, H. K., Kim, G. H., Hyun, S. K., … & Kim, H. G. (2021). Effect of process parameters for selective laser melting with SUS316L on mechanical and microstructural properties with variation in chemical composition. Materials & Design, 197, 109221. https://doi.org/https://doi.org/10.1016/j.matdes.2020.109221
  3. Deng, Y., Mao, Z., Yang, N., Niu, X., & Lu, X. (2020). Collaborative optimization of density and surface roughness of 316L stainless steel in selective laser melting. Materials (Basel), 13(7), 1601. https://doi.org/10.3390/ma13071601
  4. Dutt, A. K., Bansal, G. K., Tripathy, S., Gopala Krishna, K., Srivastava, V. C., & Ghosh Chowdhury, S. (2023). Optimization of Selective Laser Melting (SLM) Additive Manufacturing Process Parameters of 316L Austenitic Stainless Steel. Transactions of the Indian Institue of Metals, 76(2), 335–345.
  5. https://link.springer.com/article/10.1007/s12666-022-02687-2
  6. Gajera, H., Shah, D., & Pancholi, N. (2022). Effect of SLM process parameters on hardness and microstructure of stainless steel 316 material. Materials Today Proceedings, 50, 1653–1659. https://doi.org/https://doi.org/10.1016/j.matpr.2021.09.144
  7. García-Domínguez, A., Claver, J., Camacho, A. M., & Sebastián, M. A. (2020). Analysis of general and specific standardization developments in additive manufacturing from a materials and technological approach. IEEE Access, 8, 125056–125075.
  8. https://ieeexplore.ieee.org/abstract/document/9125875
  9. Gatões, D., Alves, R., Alves, B., & Vieira, M. T. (2022). Selective Laser Melting and Mechanical Properties of Stainless Steels. Materials (Basel), 15(21), 7575.https://doi.org/10.3390/ma15217575
  10. Hawk, C. (2019). Laser welding behavior of laser powder bed fusion additive manufactured 304L stainless steel. Colorado School of Mines.
  11. https://search.proquest.com/openview/b2827d1c5f49fc1f720d059ff4fdf577/1?pq-origsite=gscholar&cbl=18750&diss=y
  12. Huang, M., Zhang, Z., & Chen, P. (2019). Effect of selective laser melting process parameters on microstructure and mechanical properties of 316L stainless steel helical micro-diameter spring. The International of Journal of Advanced Manufacturing Technology, 104, 2117–2131. https://doi.org/10.1007/s00170-019-03928-3
  13. King, W. E., Barth, H. D., Castillo, V. M., Gallegos, G. F., Gibbs, J. W., Hahn, D. E., … & Rubenchik, A. M. (2014). Observation of keyhole-mode laser melting in laser powder-bed fusion additive manufacturing. Journal of Materials Processing Technology, 214(12), 2915–2925.
  14. https://doi.org/10.1016/j.jmatprotec.2014.06.005
  15. Larimian, T., AlMangour, B., Grzesiak, D., Walunj, G., & Borkar, T. (2021). Effect of laser spot size, scanning strategy, scanning speed, and laser power on microstructure and mechanical behavior of 316L stainless steel fabricated via selective laser melting. Journal of Materials Engineering and Performance, 1–20. https://link.springer.com/article/10.1007/s11665-021-06387-8
  16. Liu, J., Song, Y., Chen, C., Wang, X., Li, H., Wang, J., … & Sun, J. (2020). Effect of scanning speed on the microstructure and mechanical behavior of 316L stainless steel fabricated by selective laser melting. Materials & Design, 186, 108355.
  17. https://doi.org/10.1016/j.jmrt.2024.01.237
  18. Lu, J., Lin, X., Kang, N., Cao, Y., Wang, Q., & Huang, W. (2021). Keyhole mode induced simultaneous improvement in strength and ductility of Sc modified Al–Mn alloy manufactured by selective laser melting. Materials Science and Engineering: A, 811, 141089. https://doi.org/10.1016/j.msea.2021.141089
  19. Mashhuriazar, A., Omidvar, H., Sajuri, Z., Gur, C. H., & Baghdadi, A. H. (2020). Effects of Pre-Weld Heat Treatment and Heat Input on Metallurgical and Mechanical Behaviour in HAZ of Multi-Pass Welded IN-939 Superalloy. Metals (Basel), 10(11), 1453. https://doi.org/10.3390/met10111453
  20. Miranda, G., Faria, S., Bartolomeu, F., Pinto, E., Alves, N., & Silva, F. S. (2022). The influence of laser power and scan speed on the dimensional accuracy of Ti6Al4V thin-walled parts manufactured by selective laser melting. Metals (Basel), 12(7), 1226. https://doi.org/10.3390/met12071226
  21. Pilehrood, A. E., Mashhuriazar, A., Baghdadi, A. H., Sajuri, Z., & Omidvar, H. (2021). Effect of Laser Metal Deposition Parameters on the Characteristics of Stellite 6 Deposited Layers on Precipitation-Hardened Stainless Steel. Materials (Basel), 14(19), 5662. https://doi.org/10.3390/ma14195662
  22. Röttger, A., Boes, J., Theisen, W., Thiele, M., Esen, C., Edelmann, A., & Hellmann, R. (2020). Microstructure and mechanical properties of 316L austenitic stainless steel processed by different SLM devices. The International Journal of Advanced Manufacturing Technology, 108, 769–83.
  23. https://link.springer.com/article/10.1007/s00170-020-05371-1
  24. Spierings, A. B., Schneider, M. U., & Eggenberger, R. (2011). Comparison of density measurement techniques for additive manufactured metallic parts. Rapid Prototyping Journal, 17(5), 380-386. https://doi.org/10.1108/13552541111156504
  25. Than, L., & Percent, T. (2012). Standard Test Methods for Density of Compacted or Sintered Powder Metallurgy (PM) Products Using Archimedes’ Principle 1. i, 1–6. https://doi.org/10.1007/s11665-020-05429-x
  26. Tucho, W. M., Lysne, V. H., Austbø, H., Sjolyst-Kverneland, A., & Hansen, V. (2018). Investigation of effects of process parameters on microstructure and hardness of SLM manufactured SS316L. Journal of Alloys and Compounds, 740, 910–925. mailto:https://doi.org/10.1016/j.jallcom.2018.01.098
  27. Gong, H., Rafi, K., Gu, H., Starr, T., & Stucker, B. (2014). Analysis of defect generation in Ti–6Al–4V parts made using powder bed fusion additive manufacturing processes. Additive Manufacturing, 1, 87-98. https://doi.org/10.1016/j.addma.2014.08.002
  28. Yadroitsev, I., Yadroitsava, I., Du Plessis, A., & MacDonald, E. (2021). Fundamentals of laser powder bed fusion of metals. Elsevier. https://shop.elsevier.com/books/fundamentals-of-laser-powder-bed-fusion-of-metals/yadroitsev/978-0-12-824090-8
  29. Yang, T., Mazumder, S., Jin, Y., Squires, B., Sofield, M., Pantawane, M. V., … & Neogi, A. (2021). A Review of Diagnostics Methodologies for Metal Additive Manufacturing Processes and Products. Materials (Basel), 14(17), 4929. https://doi.org/10.3390/ma14174929
  30. Zhang, B., Dembinski, L., & Coddet, C. (2013). The study of the laser parameters and environment variables effect on mechanical properties of high compact parts elaborated by selective laser melting 316L powder. Materials Science and Engineering: A, 584, 21–31. https://doi.org/https://doi.org/10.1016/j.msea.2013.06.055
  31. Zhang, X., Yocom, C. J., Mao, B., & Liao, Y. (2019). Microstructure evolution during selective laser melting of metallic materials: A review. Journal of Laser Applications, 31(3), 31201. https://doi.org/10.2351/1.5085206
  32. Zhong, Y., Liu, L., Wikman, S., Cui, D., & Shen, Z. (2016). Intragranular cellular segregation network structure strengthening 316L stainless steel prepared by selective laser melting. Journal of Nuclear Materials, 470, 170–178. https://doi.org/10.1016/j.jnucmat.2015.12.034
  33. Ziętala, M., Durejko, T., Polański, M., Kunce, I., Płociński, T., Zieliński, W., … & Bojar, Z. (2016). The microstructure, mechanical properties and corrosion resistance of 316L stainless steel fabricated using laser engineered net shaping. Materials Science and Engineering: A, 677, 1–10. https://doi.org/https://doi.org/10.1016/j.msea.2016.09.028
  34. Tucho, W. M., Lysne, V. H., Austbø, H., Sjolyst-Kverneland, A., & Hansen, V. (2018). Investigation of effects of process parameters on microstructure and hardness of SLM manufactured SS316L. Journal of Alloys and Compounds, 740, 910-925. https://doi.org/10.1016/j.jallcom.2018.01.098
Journal of Advanced Materials and Technologies
Volume 13, Issue 2
Summer 2024
Pages 63-73

  • Receive Date 14 April 2024
  • Revise Date 08 May 2024
  • Accept Date 16 September 2024