Journal of Advanced Materials and Technologies

Journal of Advanced Materials and Technologies

Optimization of Process Parameters of the Printability of Polycaprolactone/Nano Bioactive glass Composite Scaffold Reinforced with Dorema Ammoniacum

Document Type : Original Reaearch Article

Authors
1 PhD candidate, Faculty of Materials and Metallurgical Engineering, Semnan University, Semnan, Iran.
2 Proffesor, Faculty of Materials and Metallurgical Engineering, Semnan University, Semnan, Iran.
3 Associate Proffesor, Faculty of Materials and Metallurgical Engineering, Semnan University, Semnan, Iran.
4 Associate Proffesor, Institute for Engineering in Medicine, Health, & Human Performance (EnMed), Batten College of Engineering and Technology, Old Dominion University, Norfolk, VA, 23529, USA.
10.30501/jamt.2026.597849.1373
Abstract
Background and Purpose: This study aimed to optimize both ink composition and extrusion-based three-dimensional (3D) printing parameters for the fabrication of polycaprolactone–nano-bioactive glass (PCL-BG) and polycaprolactone–nano-bioactive glass–Dorema ammoniacum (PCL-BG-DA) composite scaffolds.
Materials and Methods: PCL was dissolved in chloroform, and sol–gel-derived 45S5 nano-bioactive glass was incorporated into the solution. For DA-containing samples, Dorema ammoniacum powder was additionally added to the ink formulation. The effects of nano-bioactive glass content, the polycaprolactone-to-solvent ratio, print speed, and extrusion multiplier were evaluated using the Taguchi method. The fabricated scaffolds were characterized in terms of printability, microstructure, and compressive properties.
Results: The results demonstrated that the nano-bioactive glass content of the ink was the most influential factor affecting printability, compared with print speed and extrusion multiplier. Optimal printing conditions were achieved using a polymer-to-powder ratio of 3:1, a polymer-to-solvent ratio of 1:2, a retraction value of 1.65, an extrusion multiplier of 0.0120, and a print speed of 5. Under these conditions, scaffolds with acceptable printing quality, high reproducibility, and considerable flexibility in both shape and size were successfully fabricated. Scanning electron microscopy (SEM) images confirmed the presence of a porous and interconnected structure. The incorporation of DA reduced the compressive modulus from 53.737 MPa to 38.527 MPa.
Conclusion: The simultaneous optimization of ink composition and printing parameters enabled the successful fabrication of PCL-BG and PCL-BG-DA composite scaffolds. Nano-bioactive glass content was identified as the primary factor governing printability, while the addition of DA preserved satisfactory printability and reduced scaffold stiffness.
Keywords
Subjects

1.      Adel, I. M., ElMeligy, M. F., & Elkasabgy, N. A. (2022). Conventional and recent trends of scaffolds fabrication: a superior mode for tissue engineering. Pharmaceutics, 14(2), 306. doi: 10.3390/pharmaceutics14020306
 
2.      Ahmadi, E., Rezadoost, H., Alilou, M., Stuppner, H., & Farimani, M. M. (2022). Purification, structural characterization and antioxidant activity of a new arabinogalactan from Dorema ammoniacum gum. International journal of biological macromolecules, 194, 1019-1028. doi: 10.1016/j.ijbiomac.2021.11.163
 
3.      Borhan, S., Badr-Mohammadi, M. R., Hesaraki, S., & Esmaeilzadeh, J. (2021). Fabrication and Preliminary Characterization of Tissue Engineering Scaffolds Based on Alumina/Bioactive Glass. Advanced Ceramics Progress, 7(4), 10-19. doi: 10.30501/ACP.2022.323414.1079
 
4.      Borhan, S., & Esmaeilzadeh, J. (2021). Fabrication of Nanostructured Apatite Scaffolds by Freeze-Casting Method for Bone Tissue Engineering. Journal of Advanced Materials and Technologies, 10(2), 21-31. doi: 10.30501/jamt.2021.251760.1130
 
5.      Boroumand, N., Dini, G., Poursamar, S. A., & Asadollahi, M. A. (2025). 3D-printed polycaprolactone/mesoporous bioactive glass composite scaffolds with Mg and Zr ions for bone tissue engineering. Heliyon, 11(10). doi: 10.1016/j.heliyon.2025.e43435
 
6.      Contreras Raggio, J. I., Pardo, M., Núñez, P., Millán, C., Siqueira, G., Palza, H., ... & Aiyangar, A. K. (2025). Effect of processing parameters on the printability and mechano-biological properties of polycaprolactone–bioactive glass composites for 3D-printed scaffold fabrication. Polymers, 17(11), 1554. doi: 10.3390/polym17111554
 
7.      Emami, I., Hassanzadeh, N. N., & Bahrami, N. (2025). Fabrication and Characterization of 3D Collagen/Polycaprolactone/Hydroxyapatite Nanoparticles Scaffold Using 3D Printing Method for Repairing Damaged Bone Tissue. doi: 10.5829/ije.2025.38.10a.16
 
8.      Ferraz, M. P. (2023). Bone grafts in dental medicine: an overview of autografts, allografts and synthetic materials. Materials, 16(11), 4117. doi: 10.3390/ma16114117
 
9.      Gautam, K., Jimenez, H. G., Dikici, Y., Bensusan, J., Wnek, G. E., Rimnac, C., & Akkus, O. (2026). Optimization of 3D printing parameters for PLGA/HA scaffolds using the Taguchi method. Journal of the Mechanical Behavior of Biomedical Materials, 107385. doi: 10.1016/j.jmbbm.2026.107385
 
10.    Ghodousi-Dehnavi, E., Arjmand, M., Akbari, Z., Aminzadeh, M., & Hosseini, R. H. (2023). Anti-cancer effect of Dorema ammoniacum gum by targeting metabolic reprogramming by regulating APC, P53, KRAS gene expression in HT-29 human colon cancer cells. Reports of Biochemistry & Molecular Biology, 12(1), 127. doi: 10.52547/rbmb.12.1.127
 
11.    He, L., Yin, J., & Gao, X. (2023). Additive manufacturing of bioactive glass and its polymer composites as bone tissue engineering scaffolds: a review. Bioengineering, 10(6), 672. doi: 10.3390/bioengineering10060672
 
12.    Hutmacher, D. W. (2000). Scaffolds in tissue engineering bone and cartilage. Biomaterials, 21(24), 2529-2543. doi: 10.1016/S0142-9612(00)00121-6
 
13.    Janmohammadi, M., Nourbakhsh, M. S., & Bahraminasab, M. (2025). 3D printed polycaprolactone scaffold incorporated with tragacanth gum/bioactive glass and cellulose nanocrystals for bone tissue engineering. International Journal of Biological Macromolecules, 305, 141114. doi: 10.1016/j.ijbiomac.2025.141114
14.    Jones, J. R. (2013). Review of bioactive glass: from Hench to hybrids. Acta biomaterialia, 9(1), 4457-4486. doi: 10.1016/j.actbio.2012.08.023
 
15.    Kim, M., Nawaz, Q., Hartmann, B., Cheers, G. M., Niesner, I. C. C., Clausen-Schaumann, H., ... & Mayer-Wagner, S. (2026). 3D-printed polycaprolactone-bioactive glass composite scaffolds for bone tissue engineering: the effect of filler content on different surface modifications. Materials & Design, 116625. doi: 10.1016/j.matdes.2026.116625
 
16.    Koons, G. L., Diba, M., & Mikos, A. G. (2020). Materials design for bone-tissue engineering. Nature Reviews Materials, 5(8), 584-603. doi: 10.1038/s41578-020-0204-2
 
17.    Kumar, P., Ray, R., Kumar, S., Powar, S., & Doddamani, M. (2026). A review on direct ink writing 3D printing: Materials, properties, and future advancements. Progress in Engineering Science, 100241. doi: 10.1016/j.pes.2026.100241
 
18.    Liang, H. Y., Lee, W. K., Hsu, J. T., Shih, J. Y., Ma, T. L., Vo, T. T. T., ... & Lee, I. T. (2024). Polycaprolactone in bone tissue engineering: a comprehensive review of innovations in scaffold fabrication and surface modifications. Journal of functional biomaterials, 15(9), 243. doi: 10.3390/jfb15090243
 
19.    Marchiori, G., Bellucci, D., Gambardella, A., Petretta, M., Berni, M., Boi, M., ... & Cavallo, C. (2024). A Multidisciplinary Evaluation of Three-Dimensional Polycaprolactone Bioactive Glass Scaffolds for Bone Tissue Engineering Purposes. Materials, 17(10), 2413. doi: 10.3390/ma17102413
 
20.    Mukasheva, F., Adilova, L., Dyussenbinov, A., Yernaimanova, B., Abilev, M., & Akilbekova, D. (2024). Optimizing scaffold pore size for tissue engineering: insights across various tissue types. Frontiers in bioengineering and biotechnology, 12, 1444986. doi: 10.3389/fbioe.2024.1444986
 
21.    Murphy, C. M., & O’Brien, F. J. (2010). Understanding the effect of mean pore size on cell activity in collagen-glycosaminoglycan scaffolds. Cell adhesion & migration, 4(3), 377-381. doi: 10.4161/cam.4.3.11747
 
22.    Nawaz, Q., López, G. B., Strunk, T., Damiani, C., Mas-Moruno, C., Westhauser, F., ... & Boccaccini, A. R. (2025). 3D printing of PCL-based composite scaffolds coated with mesoporous bioactive glass nanoparticles (MBGNs) incorporating boron and molybdenum for ion-assisted bone tissue engineering. Journal of Materials Science, 60(19), 7924-7941. doi: 10.1007/s10853-025-10900-y
 
23.    Perić Kačarević, Ž., Rider, P., Alkildani, S., Retnasingh, S., Pejakić, M., Schnettler, R., ... & Barbeck, M. (2020). An introduction to bone tissue engineering. Int J Artif Organs., 43(2), 69-86. doi: 10.1177/0391398819876286
 
24.    Rabizadeh, F., & Naseri, S. (2023). Environmental parameters and habitats of Dorema ammoniacum (D. Don) in south-central Alborz Dorema ammoniacum (D. Don) habitat parameters in south-central Alborz. International Journal of Environmental Science and Technology, 20(1), 725-738.
 
25.    Rashid, K. M. J. (2023). Optimize the Taguchi method, the signal-to-noise ratio, and the sensitivity. Int. J. Stat. Appl. Math, 8(6), 64-70.
 
26.    Rau, D. A., Williams, C. B., & Bortner, M. J. (2023). Rheology and printability: A survey of critical relationships for direct ink write materials design. Progress in Materials Science, 140, 101188. doi: 10.1016/j.pmatsci.2023.101188
 
27.    Sahu, K. K., & Modi, Y. K. (2022). Multi response optimization for compressive strength, porosity and dimensional accuracy of binder jetting 3D printed ceramic bone scaffolds. Ceramics International, 48(18), 26772-26783. doi: 10.1016/j.ceramint.2022.05.375
 
28.    Tamjid, E. (2018). Three-dimensional polycaprolactone-bioactive glass composite scaffolds: Effect of particle size and volume fraction on mechanical properties and in vitro cellular behavior. International Journal of Polymeric Materials and Polymeric Biomaterials, 67(17), 1005-1015. doi: 10.1080/00914037.2017.1417285
 
29.    Tu, Y., Arrieta-Escobar, J. A., Hassan, A., Zaman, U. K. U., Siadat, A., & Yang, G. (2023). Optimizing process parameters of direct ink writing for dimensional accuracy of printed layers. 3D printing and additive manufacturing, 10(4), 816-827. doi: 10.1089/3dp.2021.0208
 
30.    Turnbull, G., Clarke, J., Picard, F., Riches, P., Jia, L., Han, F., ... & Shu, W. (2018). 3D bioactive composite scaffolds for bone tissue engineering. Bioactive materials, 3(3), 278-314. doi: 10.1016/j.bioactmat.2017.10.001
 
31.    Vallejos Baier, R., Millán Giovanetti, C., Contreras Raggio, J., & Vivanco Morales, J. F. (2022). Shape fidelity, mechanical and biological performance of 3D printed polycaprolactone-bioactive glass composite scaffolds. Biomater Adv., 134, 112540. doi: 10.1016/j.msec.2021.112540
 
32.    Wang, C., Huang, W., Zhou, Y., He, L., He, Z., Chen, Z., ... & Wang, M. (2020). 3D printing of bone tissue engineering scaffolds. Bioactive materials, 5(1), 82-91. doi: 10.1016/j.bioactmat.2020.01.004
 
33.    Wang, C., Meng, C., Zhang, Z., & Zhu, Q. (2022). 3D printing of polycaprolactone/bioactive glass composite scaffolds for in situ bone repair. Ceramics international, 48(6), 7491-7499. doi: 10.1016/j.ceramint.2021.11.293
 
34.    Woodruff, M. A., & Hutmacher, D. W. (2010). The return of a forgotten polymer—Polycaprolactone in the 21st century. Progress in polymer science, 35(10), 1217-1256. doi: 10.1016/j.progpolymsci.2010.04.002
 
35.    Zibaee, E., Amiri, M. S., Boghrati, Z., Farhadi, F., Ramezani, M., Emami, S. A., & Sahebkar, A. (2020). Ethnomedicinal uses, phytochemistry and pharmacology of Dorema species (Apiaceae): a review. Journal of pharmacopuncture, 23(3), 91. doi: 10.3831/KPI.2020.23.3.91

  • Receive Date 19 August 2026
  • Revise Date 08 September 2026
  • Accept Date 31 October 2026