Journal of Advanced Materials and Technologies

Journal of Advanced Materials and Technologies

The Effect of SiC Nanoparticles and Liquid Nitrogen Medium on Microstructure Evolutions of Severely Deformed Al During Friction Stir Processing

Authors
Mahmoud Sarkari Khorrami
Mohsen Kazeminezhad
Amir Hosein Kokabi
Sharif University of Technology, Department of Materials Science and Engineering, Tehran, Iran.
10.30501/jamt.2637.70342
Abstract
The severely deformed 1050-aluminum sheet was processed by friction stir processing (FSP) at different conditions of processing without nanoparticles in the ambient temperature and with SiC nanoparticles in the liquid Nitrogen medium. Microstructural assessments indicated that the appropriate distribution of SiC nanoparticles was obtained after 3-passes of FSP. In addition, electron backscattered diffraction (EBSD) analysis manifested that using nanoparticles along with the liquid Nitrogen medium during FSP was able to prevent the intense grain growth in the stir zone which occurred in the case of FSP without nanoparticles in the ambient temperature. Neither the orientation of grains nor the mechanism of grain formation in the stir zone was different comparing two mentioned FSP conditions. The mechanism of grain formation in the stir zone was determined to be dynamic recovery (DRV) and continuous dynamic recrystallization (CDRX) phenomena. However, discontinuous dynamic recrystallization (DDRX) mechanism was also evident in the limited extent in the case of FSP with SiC nanoparticles in the liquid Nitrogen medium. The microhardness results showed that the simultaneous use of SiC nanoparticles and liquid Nitrogen medium during FSP caused to the significant improvement in the mechanical properties of the stir zone.
Keywords
Severe plastic deformation
Friction Stir Processing
SiC nanoparticles
Liquid Nitrogen
Recrystallization
  1. Azushima A, Kopp R, Korhonen A, Yang DY, Micari F, Lahoti GD, et al. Severe plastic deformation (SPD) processes for metals. CIRP Annals - Manufacturing Technology 2008;57:716-35.
  2. Saito Y, Tsuji N, Utsunomiya H, Sakai T, Hong RG. Ultra-fine grained bulk aluminum produced by accumulative roll-bonding (ARB) process. Scripta Materialia 1998;39:1221-7.
  3. Shin HD, Park JJ, Kim YS, Park KT. Constrained groove pressing and its application to grain refinement of aluminum. Materials Science and Engineering A 2002;328:98-103.
  4. Starink MJ, Qiao XG, Zhang J, Gao N. Predicting grain refinement by cold severe plastic deformation in alloys using volume averaged dislocation generation. Acta Materialia 2009;57:5796-811.
  5. Sun Y, Fujii H, Takada Y, Tsuji N, Nakata K, Nogi K. Effect of initial grain size on the joint properties of friction stir welded aluminum. Materials Science and Engineering: A 2009;527:317-21.
  6. Su J-Q, Nelson TW, McNelley TR, Mishra RS. Development of nanocrystalline structure in Cu during friction stir processing (FSP). Materials Science and Engineering: A 2011;528:5458-64.
  7. Ueji R, Fujii H, Cui L, Nishioka A, Kunishige K, Nogi K. Friction stir welding of ultrafine grained plain low-carbon steel formed by the martensite process. Materials Science and Engineering: A 2006;423:324-30.
  8. Lilleby A, Grong Ø, Hemmer H. Cold pressure welding of severely plastically deformed aluminium by divergent extrusion. Materials Science and Engineering: A 2010;527:1351-60.
  9. Topic I, Höppel HW, Göken M. Friction stir welding of accumulative roll-bonded commercial-purity aluminium AA1050 and aluminium alloy AA6016. Materials Science and Engineering: A 2009;503:163-6.
  10. Nikulin I, Malopheyev S, Kipelova A, Kaibyshev R. Effect of SPD and friction stir welding on microstructure and mechanical properties of Al–Cu–Mg–Ag sheets. Materials Letters 2012;66:311-3.
  11. Malopheyev S, Mironov S, Kulitskiy V, Kaibyshev R. Friction-stir welding of ultra-fine grained sheets of Al–Mg–Sc–Zr alloy. Materials Science and Engineering: A 2015;624:132-9.
  12. Sarkari Khorrami M, Kazeminezhad M, Kokabi AH. Microstructure evolutions after friction stir welding of severely deformed aluminum sheets. Materials & Design 2012;40:364-72.
  13. Azizieh M, Kokabi AH, Abachi P. Effect of rotational speed and probe profile on microstructure and hardness of AZ31/Al2O3 nanocomposites fabricated by friction stir processing. Materials & Design 2011;32:2034-41.
  14. Faraji G, Asadi P. Characterization of AZ91/alumina nanocomposite produced by FSP. Materials Science and Engineering: A 2011;528:2431-40.
  15. Hsu CJ, Chang CY, Kao PW, Ho NJ, Chang CP. Al–Al3Ti nanocomposites produced in situ by friction stir processing. Acta Materialia 2006;54:5241-9.
  16. Shafiei-Zarghani A, Kashani-Bozorg SF, Hanzaki AZ. Wear assessment of Al/Al2O3 nano-composite surface layer produced using friction stir processing. Wear 2011;270:403-12.
  17. Shafiei-Zarghani A, Kashani-Bozorg SF, Zarei-Hanzaki A. Microstructures and mechanical properties of Al/Al2O3 surface nano-composite layer produced by friction stir processing. Materials Science and Engineering: A 2009;500:84-91.
  18. Chang CI, Wang YN, Pei HR, Lee CJ, Du XH, Huang JC. Microstructure and Mechanical Properties of Nano-ZrO2 and Nano-SiO2 Particulate Reinforced AZ31-Mg Based Composites Fabricated by Friction Stir Processing. Key Engineering Materials 2007;351:114-9.
  19. Asadi P, Faraji G, Masoumi A, Besharati Givi MK. Experimental Investigation of Magnesium-Base Nanocomposite Produced by Friction Stir Processing: Effects of Particle Types and Number of Friction Stir Processing Passes. Metallurgical and Materials Transactions A 2011;42:2820-32.
  20. Mazaheri Y, Karimzadeh F, Enayati MH. A novel technique for development of A356/Al2O3 surface nanocomposite by friction stir processing. Journal of Materials Processing Technology 2011;211:1614-9.
  21. Asadi P, Givi MKB, Abrinia K, Taherishargh M, Salekrostam R. Effects of SiC Particle Size and Process Parameters on the Microstructure and Hardness of AZ91/SiC Composite Layer Fabricated by FSP. Journal of Materials Engineering and Performance 2011;20:1554-62.
  22. Mishra RS, Ma ZY. Friction stir welding and processing. Materials Science and Engineering: R: Reports 2005;50:1-78.
  23. Zhang Q, Xiao BL, Wang WG, Ma ZY. Reactive mechanism and mechanical properties of in situ composites fabricated from an Al–TiO2 system by friction stir processing. Acta Materialia 2012;60:7090-103.
  24. Ajayan PM, Schadler LS, Braun PV. Nanocomposite Science and Technology. Germany-Weinheim: WILEY; 2003.
  25. Barmouz M, Asadi P, Besharati Givi MK, Taherishargh M. Investigation of mechanical properties of Cu/SiC composite fabricated by FSP: Effect of SiC particles’ size and volume fraction. Materials Science and Engineering: A 2011;528:1740-9.
  26. Khorrami MS, Kazeminezhad M, Kokabi AH. Mechanical properties of severely plastic deformed aluminum sheets joined by friction stir welding. Materials Science and Engineering: A 2012;543:243-8.
  27. Zrnik J, Kovarik T, Novy Z, Cieslar M. Ultrafine-grained structure development and deformation behavior of aluminium processed by constrained groove pressing. Materials Science and Engineering: A 2009;503:126-9.
  28. Zrnik J, Dobatkin SV, Mamuzic I. Processing of metals by severe plastic deformation (SPD)-structure and mechanical properties respond. Metalurgija 2008;47:211-6.
  29. Sato YS, Kurihara Y, Park SHC, Kokawa H, Tsuji N. Friction stir welding of ultrafine grained Al alloy 1100 produced by accumulative roll-bonding. Scripta Materialia 2004;50:57-60.
  30. Fonda RW, Bingert JF, Colligan KJ. Development of grain structure during friction stir welding. Scripta Materialia 2004;51:243-8.
  31. Su J-Q, Nelson TW, Sterling CJ. Microstructure evolution during FSW/FSP of high strength aluminum alloys. Materials Science and Engineering: A 2005;405:277-86.
  32. Gourdet S, Montheillet F. A model of continuous dynamic recrystallization. Acta Materialia 2003;51:2685-99.
  33. Pirgazi H, Akbarzadeh A, Petrov R, Kestens L. Microstructure evolution and mechanical properties of AA1100 aluminum sheet processed by accumulative roll bonding. Materials Science and Engineering: A 2008;497:132-8.

 

Journal of Advanced Materials and Technologies
Volume 5, Issue 4
Winter 2016
Pages 1-9

  • Receive Date 30 October 2015
  • Revise Date 04 December 2016
  • Accept Date 27 February 2017