Journal of Advanced Materials and Technologies

Journal of Advanced Materials and Technologies

Identification of undesirable phases and purification boron carbide - silicon carbide nanocomposite prepared by mechanically activated SHS

Authors
Hamed Roghani-Mamaghani 1
S.A. Tayebifard 1
A. Kazemzadeh 1
L. Nikzad 2
1 Semiconductor Department, Materials and Energy Research Center
2 Ceramic Department, Materials and Energy Research Center
10.30501/jamt.2635.70259
Abstract
Boron carbide - silicon carbide composite was produced by mechanically activated combustion synthesis (MASHS) method, in this study. Initially, raw materials powders containing B2O3, Si, C and Mg were weighed and were milled under Ar atmosphere by a planetary mill. For prepare pellets, the milled powders were pressed by uniaxial cold press and synthesis was occurred in atmosphere controlled tubal furnace. In the various steps, XRD analysis was taken to check the phases. XRD analysis used to calculate the average crystalline size and SEM and TEM analysis were taken to morphology studying. Resulting product is contains MgO, B4C and SiC. Also in the XRD analysis little chance
 
existence of Mg2SiO4 or borate compounds of magnesium and remaining boron, carbon and silicon are outstanding. In order to remove or reduce undesired phases, acid leaching by hydrochloric and mechanical activation with different energies were performed. The study of X-ray diffraction analysis after acid leaching showed great influence of acid leaching by HCl to remove impurities. It was also seen that remaining substances significantly reduced by activation energy increases. Average crystalline sizes of optimal sample were calculated by Scherrer equation by 11.09 for B4C and 12.66 for SiC. The SEM and TEM analysis confirmed synthesis of nanoscale boron carbide - silicon carbide composite in nano scale. Grain size of about 30 nm was observed by TEM.
Keywords
purification
silicon carbide
boron carbide
mechanical activated combustion synthesis
nanocomposites
acid leaching
  1. J. Moore, H.J. Feng, Combustion synthesis of advanced materials: Part I. Reaction parameters, Progress in Materials Science, 39 (1995) 243-273. S.T. Aruna, A.S. Mukasyan, Combustion synthesis and nanomaterials, Current Opinion in Solid State and Materials Science, 12 (2008) 44-50.
  2.     Takacs, Self-sustaining reactions induced by ball milling, Progress in Materials Science, 47 (2002) 355-414.
  3.     Nikzad, R. Licheri, M.R. Vaezi, R. Orrù, G. Cao, Chemically and mechanically activated combustion synthesis of B4C–TiB2 composites, International Journal of Refractory Metals and Hard Materials, 35 (2012) 41-48.
  4.   Deng, H.Y. Xie, L. Wang, Synthesis of submicron B4C by mechanochemical method, Materials Letters, 60 (2006) 1771-1773.
  5. Nikzad, T. Ebadzadeh, M.R. Vaezi, A. Tayebifard, Effect of milling on the combustion synthesis of ternary system B2O3, Mg and C, Micro & Nano Letters, IET, 7 (2012) 366-369.
  6. -B. Jin, J.-T. Li, M.-S. Cao, S. Agathopoulos, Influence of mechanical activation on combustion synthesis of fine silicon carbide (SiC) powder, Powder Technology, 196 (2009) 229-232.
  7. Morancais, F. Louvet, D.S. Smith, J.-P. Bonnet, High porosity SiC ceramics prepared via a process involving an SHS stage, Journal of the European Ceramic Society, 23 (2003) 1949-1956.
  8. Liu, J. Li, Y. Shan, J. Xu, Highly dense β-SiC ceramics with submicron grains prepared by sintering of nanocrystalline powders, Scripta Materialia, 67 (2012) 416-419.
  9. Zhang, X. Du, W. Wang, Z. Fu, H. Wang, Preparation of B4C–SiC composite ceramics through hot pressing assisted by mechanical alloying, International Journal of Refractory Metals and Hard Materials, 41 (2013) 270-275.
  10. C. Sahin, B. Apak, I. Akin, H.E. Kanbur, D.H. Genckan, A. Turan, G. Goller, O. Yucel, Spark plasma sintering of B4C–SiC composites, Solid State Sciences, 14 (2012) 1660-1663.
  11. Demircan, B. Derin, O. Yücel, Effect of HCl concentration on TiB2 separation from a self-propagating high-temperature synthesis (SHS) product, Materials Research Bulletin, 42 (2007) 312-318.
  12. S. Gonçalves, J.A. Carvalho, Z.M. Lima, J.M. Sasaki, Size–strain study of NiO nanoparticles by X-ray powder diffraction line broadening, Materials Letters, 72 (2012) 36-38.
  13. P. Cline, C.E. Crowder, J.A. Kaduk, S.B. Robie, D.K. Smith, R.A. Young, Recommendations for Calculated Reference Powder Diffraction Patterns, in, JCPDS-International Centre for Diffraction Data, 1996.
  14. X'Pert HighScore Plus, in, PANalytical B.V, 2006.
  15. Alkan, M.S. Sonmez, B. Derin, O. Yücel, Effect of initial composition on boron carbide production by SHS process followed by acid leaching, Solid State Sciences, 14 (2012) 1688-1691.
  16. S. Pokrovsky, J. Schott, Kinetics and mechanism of forsterite dissolution at 25°C and pH from 1 to 12, Geochimica et Cosmochimica Acta, 64 (2000) 3313-3325.
  17. David Halliday, Robert Resnick, J. Walker, FUNDAMENTALS OF PHYSICS, John Wiley & Sons, Inc, 2011.
  18. س.ع. طیبی فرد, بررسی پارامترهای موثر بر سنتز مولیبدن دی سیلیساید پژوهشگاه مواد و انرژی، 1377.
  19.   H. Wu, M. Gao, D. Zhu, S. Zhang, Y. Pan, H. Pan, Y. Liu, F.J. Oliveira, J.M. Vieira, SiC whisker reinforced multi-carbides composites prepared from B4C and pyrolyzed rice husks via reactive infiltration, Ceramics International, 38 (2012) 3519-3527.
Journal of Advanced Materials and Technologies
Volume 3, Issue 2
Summer 2014
Pages 19-25

  • Receive Date 12 November 2013
  • Revise Date 25 February 2014
  • Accept Date 02 March 2014