Journal of Advanced Materials and Technologies

Journal of Advanced Materials and Technologies

Effect of WC Addition on the Wear Resistance of Mullite-WC Composites Sintered by Spark Plasma Sintering

Document Type : Original Reaearch Article

Authors
Hosein Rajaei 1
Milad Bahamirian 2
Iman Mobasherpour 3
Mohammad Zakeri 3
Mohammad Farvizi 3
1 Instructor, Department of Ceramic, Materials and Energy Research Center, Karaj, Iran
2 Assistant Professor, Department of Mining and Metallurgical Engineering, Yazd University, Yazd, Iran
3 Associate Professor, Department of Ceramic, Materials and Energy Research Center, Karaj, Iran
10.30501/jamt.2022.350273.1236
Abstract
This study aims to improve the wear resistance of mullite ceramics as one of the most critical engineering ceramics by adding tungsten carbide (WC) particles. For this purpose, mullite-WC composites without and with adding 5, 10, and 15 % by weight of WC particles produced by Spark Plasma Sintering (SPS) method. In addition, it investigates the effect of sintering temperature on the wear resistance of mullite-WC composites applied by the SPS process at 1300 °C, 1350 °C, 1400 °C, and 1450 °C for 4 minutes under the pressure of 30 MPa. The results pin on the disk testing indicates that upon increasing the weight percentage of WC particles and increasing the sintering temperature up to 1400 °C, the wear resistance of mullite-WC composites would increase. However, increasing the sintering temperature up to the range of 1450 °C led to a decrease in the wear resistance due to the poor mechanical properties and formation of the W2C phase. The results from Scanning Electron Microscopy (FESEM) analysis are indicative of the formation of abrasive wear and surface layer structure mechanisms on the surface in mullite ceramics samples with and without WC reinforcing particles.
 
Keywords
Spark Plasma Sintering (SPS)
Mullite
Tungsten Carbide
Wear
Composite

Subjects

  1. Rajaei, H., Mobasherpour, I., Farvizi, M., Zakeri, M., "Effect of mullite synthesis methods on the spark plasma sintering behaviour and mechanical properties", Micro & Nano Letters, Vol. 11, No. 8, (2016), 465-468. https://doi.org/10.1049/mnl.2016.0092
  2. Schneider, H., Schreuer, J., Hildmann, B., "Hildmann, structure and properties of mullite—A review", Journal of the European Ceramic Society, Vol. 28, No. 2, (2008), 329-344. https://doi.org/10.1016/j.jeurceramsoc.2007.03.017
  3. Ghahremani, D., Ebadzadeh, T., Maghsodipour., A., "Densification, microstructure and mechanical properties of mullite–TiC composites prepared by spark plasma sintering", Ceramics International, Vol. 41, No. 2, (2015), 1957-1962. https://doi.org/10.1016/j.ceramint.2014.07.146
  4. Warrier, K. G. K., Anilkumar, G. M., "Densification of mullite–SiC nanocomposite sol–gel precursors by pressureless sintering", Materials Chemistry and Physics, Vol. 67, No. 1-3, (2001), 263-266. https://doi.org/10.1016/S0254-0584(00)00447-8
  5. Ando, K., Chu, M. C., Tsuji, K., Hirasawa, T., Kobayashi, Y., Sato, S., "Crack healing behaviour and high-temperature strength of mullite/SiC composite ceramics", Journal of the European Ceramic Society, Vol. 22, No. 8, (2002), 1313-1319. https://doi.org/10.1016/S0955-2219(01)00431-9
  6. Rajaei, H., Mobasherpour, I., Farvizi, M., Zakeri, M., "Effect of composition on mechanical properties of mullite-WC nano composites prepared by spark plasma sintering", Tribology in Industry, Vol. 38, No. 4, (2016), 552-558. https://doaj.org/article/c470bcdbf6e7408e93fad5607250c7b9
  7. Rajaei, H., Farvizi, M., Mobasherpour, I., Zakeri, M., "Effect of spark plasma sintering temperature on microstructure and mechanical properties of mullite-WC composites", International Journal of Refractory Metals and Hard Materials, Vol. 70, (2018), 197-201. https://doi.org/10.1016/j.ijrmhm.2017.10.012
  8. Ghasali, E., Orooji, Y., Faeghinia, A., Alizadeh, M., Ebadzadeh, T., "Characterization of mullite-Nd2O3 composite prepared through spark plasma sintering", Ceramics International, Vol. 47, No. 11, (2021), 16200-16207. https://doi.org/10.1016/j.ceramint.2021.02.198
  9. Ghasali, E., Ghahremani, D., Orooji, Y., Faeghinia, A., Kazem-zadeh, A., Ebadzadeh, T., "Microstructure and phase formation of mullite-Pr6O11 composite prepared by spark plasma sintering", Journal of Rare Earths, Vol. 41, No. 2, (2023), 283-289. https://doi.org/10.1016/j.jre.2022.03.018
  10. Taimatsu, H., Sugiyama, S., Kodaira, Y., "Synthesis of W2C by reactive hot pressing and its mechanical properties", Materials Transactions, Vol. 49, (2008), 0804070390-0804070390. https://doi.org/10.2320/matertrans.MRA2007304
  11. Chen, W. H., Lin, H. T., Nayak, P. K., Huang, J. L., "Material properties of tungsten carbide–alumina composites fabricated by spark plasma sintering", Ceramics International, Vol. 40, No. 9, (2014), 15007-15012. https://doi.org/10.1016/j.ceramint.2014.06.102
  12. Chen, C. Y., Lan, G. S., Tuan, W. H., "Preparation of mullite by the reaction sintering of kaolinite and alumina", Journal of the European Ceramic Society, Vol. 20, No. 14-15, (2000), 2519-2525. https://doi.org/10.1016/S0955-2219(00)00125-4
  13. Kanka, B., Schneider, H., "Sintering mechanisms and microstructural development of coprecipitated mullite", Journal of Materials Science, Vol. 29, No. 5, (1994), 1239-1249. https://doi.org/10.1007/BF00975071
  14. Ghahremani, D., Ebadzadeh, T., Maghsodipour, A. "Spark plasma sintering of mullite: relation between microstructure, properties and spark plasma sintering (SPS) parameters", Ceramics International, Vol. 41, No. 5, (2015), 6409-6416. https://doi.org/10.1016/j.ceramint.2015.01.078
  15. Gao, L., Jin, X., Kawaoka, H., Sekino, T., Niihara, K., "Microstructure and mechanical properties of SiC–mullite nanocomposite prepared by spark plasma sintering", Materials Science and Engineering: A, Vol. 334, No. 1-2, (2002), 262-266. https://doi.org/10.1016/S0921-5093(01)01898-6
  16. Orooji, Y., Ghasali, E., Moradi, M., Derakhshandeh, M. R., Alizadeh, M., Shahedi Asl, M., Ebadzadeh, T., "Preparation of mullite-TiB2-CNTs hybrid composite through spark plasma sintering", Ceramics International, Vol. 45, No. 13, (2019), 16288-16296. https://doi.org/10.1016/j.ceramint.2019.05.154
  17. Orooji, Y., Alizadeh, A. A., Ghasali, E., Derakhshandeh, M. R., Alizadeh, M., Shahedi Asl, M., Ebadzadeh, T., "Co-reinforcing of mullite-TiN-CNT composites with ZrB2 and TiB2 compounds", Ceramics International, Vol 45, No. 16, (2019), 20844-20854. https://doi.org/10.1016/j.ceramint.2019.07.072
  18. Standard Test Method for Pin Abrasion Testing, in ASTM G132-96, (2018). https://doi.org/10.1520/G0132-96R13
  19. Lancaster, J. K., "A review of the influence of environmental humidity and water on friction, lubrication and wear", Tribology International, Vol. 23, No. 6, (1990), 371-389. https://doi.org/10.1016/0301-679X(90)90053-R

 

 

Journal of Advanced Materials and Technologies
Volume 12, Issue 1
Spring 2023
Pages 57-69

  • Receive Date 04 July 2022
  • Revise Date 14 September 2022
  • Accept Date 08 October 2022