پژوهشگاه مواد و انرژیمواد و فناوریهای پیشرفته2783-08107120180522Design Experiment Methods for Optimization of Aluminum Anodize Coating Hardnessروش طراحی آزمایش به منظور بهینه سازی سختی پوششهای آندایزینگ آلومینیوم199148310.30501/jamt.2018.91483FAایمان محمدیدانشگاه صنعتی شریف، دانشکده مهندسی و علم مواد، تهران، ایرانمزدک ایزدیدانشگاه تربیت مدرس، دانشکده فنی و مهندسی، تهران، ایرانمحمد فاروقیدانشگاه صنعتی شریف، دانشکده مهندسی و علم مواد، تهران، ایرانعبدالله افشاردانشگاه صنعتی شریف، دانشکده مهندسی و علم مواد، تهران، ایرانJournal Article20190731The aim of this work is to optimize the hardness of anodizing aluminum coating by design of experimental method. Various parameters affect the hardness of these coatings among which time, temperature and pulse current parameters (current density limit, frequency and duty cycle) were considered. According to this, mentioned parameters in different levels were considered as input variables. Also, the effect of parameters on the hardness of anodizing aluminum coating was obtained as a mathematical model. The final model was achieved by Analysis of variance which was used for attaining the best method to predict the maximum hardness of these coatings. The most effective variables and optimized hardness of anodizing aluminum coating were obtained by using the mathematical model. Experimental<br />results showed that temperature and quadratic behavior of duty cycle were the most important terms on the hardness of<br />these coatings. Furthermore, the maximum hardness of this coating was 491Hv, which was attained at the maximum<br />and minimum current densities of 4.09, 1.23 A/dm2 , frequency of 146.94 Hz, time of 29.50 min, duty cycle of 65.16%<br />and the bath temperature of 3.13o C.در این پژوهش هدف این است که سختی پوشش آندایزینگ آلومینیوم بهکمک روش طراحی آزمایش بهینه شود. متغیرهای متفاوتی بر سختی این پوشش مؤثر می باشند که از مهمترین آنها می توان به زمان، دما و متغیرهای مربوط به جریان پالسی (دانسیته جریان حداکثر و حداقل، فرکانس و چرخه کاری) اشاره کرد. در این راستا متغیرهای مذکور در سطوح مختلف بهعنوان ورودی فرآیند طراحی آزمایش در نظر گرفته شد. همچنین اثر این متغیرها بر سختی پوشش آندایزینگ آلومینیوم بهصورت یک مدل ریاضی بهعنوان خروجی بهدست آمد. برای رسیدن به مدل نهایی از روش آنالیز تغییرات به منظور دستیابی به بهترین روش برای رسیدن به حداکثر سختی پوشش استفاده شد. با استفاده از این مدل ریاضی علاوه بر اینکه امکان تعیین مؤثرترین متغیرها وجود دارد، میتوان بهینه مقدار سختی را نیز بهعنوان خروجی فرآیند بهدست آورد. نتایج نشان داد که دما و مربع چرخهی کاری مهمترین متغیرهای تأثیرگذار بر سختی این پوششها هستند. همچنین پوششی با سختی Hv 491 در شرایط کاری دمای <sup>o</sup>C 13/3 ، زمان min 50/29 ، چرخه کاری 16/ 65 درصد، فرکانس Hz 94/146، جریان حداکثر A/dm<sup>2</sup> 09/4 و حداقل A/dm<sup>2</sup> 23/1 ایجاد شد.https://www.jamt.ir/article_91483_358ca3dfa695cbe8739b5b9966dc2ed4.pdfپژوهشگاه مواد و انرژیمواد و فناوریهای پیشرفته2783-08107120180522Removal of Cadmium (II) Using CoFe2O4 Powders Synthesized by Solution Combustion Methodحذف یون کادمیم از محلول آبی توسط پودرهای CoFe2O4 تهیه شده به روش سنتز احتراق محلولی11179161910.30501/jamt.2018.91619FAبنفشه پورگل محمددانشگاه علم و صنعت ایران، دانشکده مهندسی مواد و متالورژی، تهران، ایرانسید مرتضی مسعودپناهدانشگاه علم و صنعت ایران، دانشکده مهندسی مواد و متالورژی، تهران، ایران0000-0002-5950-0806محمدرضا ابوطالبیدانشگاه علم و صنعت ایران، دانشکده مهندسی مواد و متالورژی، تهران، ایرانJournal Article20180104Cobalt ferrite (CoFe<sub>2</sub>O<sub>4</sub>) powders were successfully prepared by solution combustion synthesis using metal nitrates as oxidant and glycine as fuel at various fuel to oxidant molar ratios (f=0.5, 0.75, 1 and 1.25). The structure, morphology and specific surface area of as-combusted CoFe<sub>2</sub>O<sub>4</sub> powders were characterized by X-ray diffraction, scanning electron microscopy and nitrogen adsorption-desorption techniques. By increasing of fuel content, the specific surface area and pore volume decreased from 285 to 35 m<sup>2</sup>/g and 1.38 to 0.17 cm<sup>3</sup>/g, respectively. The as-combusted magnetic CoFe<sub>2</sub>O<sub>4</sub> powders were used as adsorbent for removal of Cd(II). The effect of the contact time showed the kinetics of adsorption process followed the pseudo-second-order model and was controlled by film diffusion process. The adsorption isotherms were also well fitted on the Freundlich model. The as-combusted CoFe<sub>2</sub>O<sub>4</sub> powders at f=0.75 exhibited excellent adsorption capacity (694 mg g<sup>−1</sup>) and high adsorption rate.در این پژوهش، پودرهای تک فاز فریت کبالت (CoFe<sub>2</sub>O<sub>4</sub>) توسط روش سنتز احتراق محلولی با استفاده از نیترات های فلزی به عنوان اکسنده و گلایسین به عنوان سوخت در مقادیر متفاوت نسبت مولی سوخت به اکسنده (f) برابر با 5/0، 75/0، 1 و 25/1 تهیه شدند. ساختار، مورفولوژی و مساحت سطح ویژه پودرهای فریت کبالت احتراق یافته توسط روش هایی چون پراش پرتو ایکس، میکروسکوپ الکترونی روبشی، جذب-واجذب نیتروژن ارزیابی شدند. با افزایش مقدار سوخت، مساحت سطح ویژه و حجم تخلخل به ترتیب از 285 به m<sup>2</sup>/g 35 و 38/1 به cm<sup>3</sup>/g 17/0 کاهش یافتند. پودرهای فریت کبالت احتراق یافته به عنوان جاذب برای حذف یون کادمیم از محلول آبی استفاده شدند. بررسی زمان تماس نشان داد که سینتیک فرآیند جذب از مدل شبه مرتبه دوم پیروی می کند. ایزوترم های جذب به خوبی بر مدل فردلیچ منطبق شدند و بیشترین میزان ظرفیت جذب ( mg/g 694) توسط پودرهای فریت کبالت احتراق یافته در نسبت مولی سوخت به اکسنده برابر با 75/0 بدست آمد.https://www.jamt.ir/article_91619_a1ee35d354238d98e985a7f1ef9d01d2.pdfپژوهشگاه مواد و انرژیمواد و فناوریهای پیشرفته2783-08107120180522Optimization of the Production Process in Cobalt-Tungsten Carbide Nanopowder by Mechanical Millingبهینه سازی فرآیند تولید نانو پودر کاربید تنگستن محتوی کبالت به وسیله آسیاب کاری مکانیکی19279162210.30501/jamt.2018.91622FAاحمد صادقی فیروزجاییدانشگاه صنعتی خواجه نصیرالدین طوسی، دانشکده مهندسی و علم مواد، تهران، ایرانحمید خرسنددانشگاه صنعتی خواجه نصیرالدین طوسی، دانشکده مهندسی و علم مواد، تهران، ایران0000-0002-1026-2077Journal Article20150920Tungsten carbides are used in cutting blades and other similar items because of their high hardness. In this study, tungsten carbide (WC) powder and cobalt (Co) powder in size of less than 10 microns and weight ratio of 94% tungsten carbide and 6% cobalt (WC-6% Co) were mixed together in a high-energy mechanical milling. Then they milled in various ratios of ball to powder and time. Milled samples were studied using scanning electron microscopy (SEM). The results obtained were compared by microscopy and EDX elemental analysis. Optimized powder for the production of powder metallurgy sample was selected and sintered. Metallography and hardness testing and SEM imaging was performed on sintered sample. The results showed a significant improvement in grain size to reach below 100 nm in the milled powders and in the sintered samples were reaching below 150 nm. Vickers hardness in the final sample reached in 1752.در این تحقیق از پودر اولیه کاربید تنگستن و کبالت با اندازه های میکرونی، نانوپودر کاربید تنگستن محتوی کبالت ساخته و از نانوپودر بهینه نمونه متالورژی پودر ساخته شد و مراحل آسیاب کاری فرآیند مورد بررسی قرار گرفت. پودر کاربید تنگستن (WC) و پودر کبالت (Co) در اندازه کمتر از 10 میکرون به نسبت وزنی 94 درصد کاربید تنگستن و 6 درصد کبالت (WC-6%Co)با هم مخلوط شده و در آسیاب مکانیکی پرانرژی قرار گرفت. سپس پودر با نسبتهای مختلف گلوله به پودر و در زمانهای متفاوت آسیاب شد. از نمونههای آسیاب شده با استفاده از میکروسکوپ الکترونی روبشی (SEM) تصویر برداری شد و آنالیز عنصری EDX روی آنها اعمال شد. با بررسی نتایج پودر بهینه برای تولید نمونه جهت متالوگرافی و سختی سنجی انتخاب شد و نمونه به روش متالورژی پودر معمولی ساخته شد. آزمونهای متالوگرافی و سختی سنجی و تصویربرداری با SEM روی نمونه تفجوشی شده انجام شد. نتایج حاصله نشان دهنده بهبود اندازه دانه و رسیدن آن به زیر 100 نانومتر در پودرهای آسیاب شده و رسیدن به زیر 150 نانومتر در نمونه تفجوشی شده است و سختی نمونه نهایی به 1752 ویکرز رسیده است.https://www.jamt.ir/article_91622_dbcc5700b9b92ad009d45a12dcfed5e4.pdfپژوهشگاه مواد و انرژیمواد و فناوریهای پیشرفته2783-08107120180522Enhanced Surface Adhesion of Graphene Oxide Thin Film on Hydrophobic Silicon Substrateافزایش چسبندگی سطحی لایهنازک اکسیدگرافن روی بستر سیلیکون آب گریز29339162610.30501/jamt.2018.91626FAساناز راثیپژوهشگاه مواد و انرژی، پژوهشکده نانوتکنولوژی و مواد پیشرفته، کرج، ایراننیما نادریپژوهشگاه مواد و انرژی، پژوهشکده نانوتکنولوژی و مواد پیشرفته، کرج، ایرانمرتضی مرادی البرزیپژوهشگاه مواد و انرژی، پژوهشکده نانوتکنولوژی و مواد پیشرفته، کرج، ایران0000-0003-2361-4796Journal Article20161214In the present work, charged graphene oxide (GO) layers were synthesized using conventional modified Hummer’s method. A thin film of GO was deposited using electrophoretic deposition technique from stable aqueous colloidal suspension of GO layers on hydrophobic surface of crystalline silicon (c-Si) samples. Surface modification with Ag particles was performed in order to improve surface adhesion of graphene oxide layers on hydrophobic silicon surface. Reduction process of deposited GO layer was performed at a temperature of 400 ºC under argon gas flow. The x-ray diffraction pattern showed that graphite layers with oxygen functional groups and increased interlayer spacing were successfully obtained using improved Hummer’s technique. Scanning electron microscopy micrographs showed that non-uniform GO layers were formed on silicon hydrophobic surface. Enhanced surface adhesion and deposition of a uniform thin film of GO was achieved via surface modification using Ag particles. Raman spectra of deposited films proved the existence of GO layers which were reduced.در این تحقیق، لایه های اکسیدگرافن[1] باردار توسط روش رایج اصلاح شده هامر[2]، سنتز گردید. لایه نازک اکسید گرافن به روش لایه نشانی الکتروفورتیک[3] توسط سوسپانسیون کلوئیدی آبی اکسید گرافن روی زیر لایه سیلیکون [4] لایه نشانی شد. جهت بهبود میزان چسبندگی لایه های اکسید گرافن روی سطح آبگریز سیلیکون، عملیات اصلاح سطح زیرلایه توسط ذرات نقره انجام گرفت. فرایند احیا اکسید گرافن لایه نشانی شده در دمای ºC400 تحت جریان آرگون انجام شد. الگوی پراش اشعه ی ایکس عامل دار شدن لایه های گرافیت با گروه های عاملی اکسیژنی و افزایش موفقیت آمیز فاصله بین صفحه ای توسط متد هامر اصلاح شده را تایید می کند. تصاویر میکروسکوپ الکترونی روبشی گسیل میدانی از نمونه لایه نشانی شده روی بستر سیلکون اصلاح نشده، لایه نشانی غیر یکنواخت و جزئی اکسید گرافن را نشان می دهد. بهبود میزان چسبندگی و لایه نشانی یکنواخت لایه نازک اکسید گرافن پس از اصلاح سطح سیلیکون توسط ذرات نقره حاصل شد. طیفسنجی رامان حاصل از این نمونه شکل گیری لایه نازک اکسید گرافن احیا شده را تایید می کند.<br /> https://www.jamt.ir/article_91626_d205cc6aecfd4ddeebdead1f39d8bf0b.pdfپژوهشگاه مواد و انرژیمواد و فناوریهای پیشرفته2783-08107120180522Effect of Copper Addition on the Microstructure, Hardness and Antibacterial Properties of Martensitic Stainless Steel (410s)تاثیر افزودن مس بر ریزساختار، سختی و خواص ضدمیکروبی فولاد زنگ نزن مارتنزیتی (410s)35449162710.30501/jamt.2018.91627FAمهدی بهمنی اسکوییدانشگاه صنعتی سهند، دانشکده مهندسی مواد تبریز، ایرانسیامک حسین نژاددانشکده صنعتی سهند، دانشکده مهندسی مواد، تبریز، ایراناحد صمدیدانشگاه صنعتی سهند، دانشکده مهندسی مواد ، تبریز، ایرانJournal Article20171115Effect of Cu addition (5 wt.% ) on the microstructure, hardness and antibacterial properties of the martensitic stainless steel (AISI 410s ) was investigated by means of scanning electron microscopy (SEM), scanning transmission electron microscopy (STEM) and hardness measurement. Antibacterial performance was evaluated according to JIS Z 2801:2000 against Escherichia coli (E. coli) bacteria, the common pathogen of human disease. After austenitization treatment at 1050 °C in a salt bath and oil quenching, the AISI 410s steel showed dual phase martensite-ferrite microstructure. Addition of about 5 wt.% Cu eliminated ferrite and led to a fully martensitic microstructure in the quenched condition. The latter associated with primary Cu precipitates formed during austenitization treatment. Aging treatment of the quenched steels was carried out at 500-700 °C for one hour in a salt bath. Transmission electron microscopy (TEM) revealed the formation of fine, Cu-rich precipitates in aged Cu-bearing stainless steel (AISI 410s-Cu). After aging for one hour at 500 °C, hardness of AISI 410s steel increased for 30 HV while that of AISI410s-Cu steel increased for about 100 Hv. AISI 410s steel represented no antibacterial performance against the E. coli bacteria but hopefully AISI 410s-Cu stainless steel exhibited strong antibacterial performance. Both of the primary and aging Cu precipitates are thought to release Cu ions to biological environment which act toxically against the E. coli bacteria.تاثیر افزودن مس (حدود 5 درصد وزنی) برریزساختار و سختی فولاد زنگ نزن مارتنزیتی (AISI 410s) بوسیله میکروسکوپ الکترونی روبشی، میکروسکوپ الکترونی عبوری- روبشی و سختی سنجی ویکرز مورد بررسی قرار گرفته و رفتار پادمیکروبی آن بر اساس استاندارد JIS Z 2801:2000 بر علیه باکتری اشرشیاکلی -یکی از باکتری های عامل بیماری انسان- ارزیابی شد. پس از عملیات آستنیته کردن در دمای C° 1050 درون حمام نمک و کوئنچ در روغن، ریزساختار دوفازی مارتنزیت-فریت در تصاویر میکروسکوپ الکترونی روبشی فولاد AISI 410s مشاهده شد. افزودن مس به این فولاد (AISI 410s-Cu) سبب حذف فریت و تشکیل ساختار کاملا مارتنزیتی میشود. ساختار مارتنزیتی دارای رسوبات غیرهمگن مس نیز هست که در دمای بالا و در مرز دانههای آستنیت اولیه تشکیل میشوند و وجود آنها برابر تعادل فازی FCC+(Cu) در دمای آستنیته توجیه میگردد. پیرسازی فولادهای آستنیته و کوئنچ شده در سه دمای 500، 600 و 700 (C°) و به مدت زمان ثابت یک ساعت درون حمام نمک انجام گرفت. نتایج نشان داد که پیرسازی در دمای C° 500 سبب افزایش سختی فولاد 410s به میزان 30 ویکرز شده ولی سختی فولاد AISI 410s-Cu به میزان 100 ویکرز افزایش مییابد. پیرسازی در دماهای 600 و 700 (C°) سبب کاهش سختی میشود. تصاویر میکروسکوپ الکترونی عبوری و آنالیزهای شیمیایی دقیق، تشکیل رسوبات ریز غنی از مس در فولاد AISI 410s-Cu پیرشده در دمای C°500 را نشان داد. این رسوبات علاوه بر رسوبات مس اولیه بوده و سبب افزایش سختی میشوند. پیرسازی در دماهای بالاتر سبب رشد رسوبات و تغییر مورفولوژی آنها شده و اثر استحکام بخشی آنها را کم میکند. نتایج آزمون پادمیکروبی نشان دهنده عدم خاصیت پادمیکروبی در فولاد AISI 410s و در مقابل آن خاصیت پادمیکروبی قوی در فولاد AISI 410s-Cu در برابر باکتری اشرشیاکلی میباشد.https://www.jamt.ir/article_91627_6d7d3657ea57a20fc994191850ac7645.pdfپژوهشگاه مواد و انرژیمواد و فناوریهای پیشرفته2783-08107120180522Fabrication of Adsorbent from Coconut Coir by EDM Method for Removal of Nitrate from Aqueous Solutionsساخت جاذب از الیاف نارگیل با استفاده از روش EDM و بررسی رفتار آن در حذف نیترات از محلول های آبی 45529167810.30501/jamt.2018.91678FAنوشین سلمان تبریزیپژوهشگاه مواد و انرژی، پژوهشکده انرژی، کرج، ایران0000-0002-6125-3998مریم یاوریپژوهشگاه مواد و انرژی، پژوهشکده انرژی، کرج، ایراننوشین رئیسی خیرآبادیپژوهشگاه مواد و انرژی، پژوهشکده فناوری نانو و مواد پیشرفته، کرج، ایرانJournal Article20170613In this work crushed coconut coir was chemically modified by EDM method and its <em></em>performance as adsorbent for removal of nitrate from aqueous solutions was investigated. In this regard, the effect of various parameters like time, adsorbent dosage, nitrate initial concentration, pH, and temperature on the adsorption process was studied. It was <em></em>observed that the kinetic data followed the pseudo-first order kinetic model and the adsorption <em></em>isotherms were properly fitted to Langmuir model. Thermodynamic analysis showed that the <em></em>adsorption process was spontaneous, exothermic with decreased randomness at solid-liquid <em></em>interface. Moreover, the adsorbent showed a superior performance at neutral pH and the adsorbed <em></em>nitrate could easily be desorbed by adjusting pH of the solution suggesting the reusability of the <em></em>adsorbent.<em></em>در این تحقیق الیاف خرد شده نارگیل با روش شیمیایی [1] EDM اصلاح شده و از آن جهت حذف یون نیترات از آب استفاده و رفتار آن در فرآیند جذب سطحی مورد بررسی قرار گرفته است. در این راستا اثر پارامترهای مختلف در فرآیند جذب سطحی از قبیل اثر زمان، وزن جاذب، غلظت اولیه نیترات، pH، درجه حرارت در حذف نیترات تعیین گردید. آزمایش ها نشان دادند که داده های سینتیکی با معادله شبه درجه اول مطابقت خوبی داشته و ایزوترم های جذب از مدل جذب تک لایه Langmuir متابعت می نمایند. همچنین بررسی های ترمودینامیکی نشان دادند که واکنش جذب خودبخودی، گرمازا و با کاهش بی نظمی در فصل مشترک مایع- جامد همراه بوده است. طبق نتایج آزمایشگاهی جاذب در pH خنثی جذب بیشتری نشان داده و آزمایش های واجذب نشان دادند که نیترات جذب شده توسط جاذب با تغییر pH قابل واجذب بوده و لذا جاذب سنتز شده قابلیت استفاده مجدد را دارد. https://www.jamt.ir/article_91678_679f60136ebdc0e277d0243618c804c5.pdfپژوهشگاه مواد و انرژیمواد و فناوریهای پیشرفته2783-08107120180522Synthesis and Characterization of Hydrogel Loaded Curcumin Encapsulated Chitosan Nanoparticles as Novel Wound Dressingساخت و مشخصه یابی هیدروژل حاوی کورکومین بارگذاری شده در نانوذرات کیتوسان به عنوان زخم پوش نوین53639168110.30501/jamt.2018.91681FAسید احمد میرزاباباییدانشگاه آزاد اسلامی، واحد یزد، گروه مهندسی پزشکی، یزد، ایرانمحبوبه محمودیدانشگاه آزاد اسلامی، واحد یزد، گروه مهندسی پزشکی، یزد، ایران0000-0002-9763-6587رضیه موهبتدانشگاه آزاد اسلامی، واحد یزد، گروه شیمی، یزد، ایرانJournal Article20171024In this study, curcumin/chitosan (Cs/Cr) nanocomplex with different weight percentages Cs/Cr (1:1) (sample A) and Cs/Cr (2:1) (sample B) by drug-poly saccharide complex method were fabricated and encapsulated into chitosan/alginate hydrogel and then the samples were evaluated. The morphology and functional group of the samples surface were evaluated via the scanning electron microscopy (SEM and FESEM) and fourier transform infrared spectroscopy (FTIR), respectively. The average hydrodynamic diameter of nancomplex A and B by the dynamic light scattering (DLS) were measured 80nm and 45 nm, respectively and their zeta potentials were obtained +18 mV and +24 mV, respectively. For characterization of Cs/Cr nano complex loaded hydrogel, the water vapour transmission rate (WVTR) and the swelling test in PBS were performed. The results indicated that hydrogel containing nanocomplex B with high absorbing fluids (2049%) and good WVTR (2300 g/m<sup>2</sup>/day) can be suitable for creating a wet environment for wound healing. Also, in vitro release studies by HPLC method was performed for evaluation of curcumin release from nano complex and the results showed a sustained release without initial burst release. To study the release mechanism of curcumin from nanocomplex, data obtained from release test were fitted to Korsmeyer-Peppas kinetics model. Also, the encapsulation efficiency of curcumin in nanocomplex was meseared 80% that the results indicated a high curcumin loading in nanocomplex. Finally, the viability and proliferation of fibroblast cell line (L929) on nano complex surface was evaluated by MTT assay and the results did not showed any cytotoxicity. Therefore, the hydrogel containing Cs/Cr nano complex can be a good choice as wound dressing for rapid healing. در این تحقیق، نانو کمپلکس کیتوسان / کورکومین(Cs/Cr) با درصد وزنی (1:1) Cr/Cs (نمونه A) و (2:1) Cr/Cs (نمونه B) با روش کمپلکس دارو- پلی ساکارید ساخته شد و در داخل هیدروژل آلژینات/ کیتوسان کپسوله و مورد ارزیابی قرار گرفت. مورفولوژی سطح و گروه های عاملی موجود در روی سطح نمونه ها به ترتیب با میکروسکوپ (SEM و (FESEM و FTIR ارزیابی گردید. متوسط قطر هیدرودینامیکی نانوکمپلکس A و B با روش پراکندگی دینامیکی نور ((DLS به ترتیب در محدوده nm 80 و nm 45 و بار سطحی آن ها به ترتیب mV 18+ و mV 24+ محاسبه شد. برای مشخصه یابی هیدروژل حاوی نانوکمپلکس Cr/Cs، تست عبور بخار و آزمون درصد تورم در محلول بافر فسفات انجام گرفت. نتایج نشان داد، هیدروژل حاوی نانوکمپلکس B دارای میزان تورم و عبور بخار به ترتیب 2049% و g/m<sup>2</sup>/day 2300 می باشد که می تواند محیط ترمیم مرطوب را در محل زخم ایجاد نماید. همچنین، برای سنجش رهایش کورکومین از نانوکمپلکس ها، مطالعات رهایش در in vitro با روش HPLC که رهایش آهسته بدون رهایش انفجاری را نشان داد، انجام گرفت. سپس جهت بررسی مکانیزم رهایش کورکومین از نانوکمپلکس ها، نتایج حاصل از ازمون رهایش دارو با مدل کورسمایر- پپاس تطبیق داده شد. همچنین، میزان کپسوله شدن کورکومین در نانوکمپلکس 80% محاسبه گردید که نشان دهنده بارگذاری بالای کورکومین در نانوکمپلکس می باشد. در نهایت، توسط آزمون سمیت سلولی (MTT)، میزان تکثیر و زنده مانی سلول های فیبروبلاست (L929) بر روی سطح نانو کمپلکس بررسی گردید و نتایج هیچ گونه سمیتی سلولی را در نانو کمپلکس نشان نداد. بنابراین، هیدروژل حاوی نانو کمپلکس کیتوسان / کورکومین می تواند کاربرد بالقوه ای را به عنوان زخم پوش برای تسریع در ترمیم زخم داشته باشد.https://www.jamt.ir/article_91681_1f31e8efc2e7b4330e8b08af7214d094.pdfپژوهشگاه مواد و انرژیمواد و فناوریهای پیشرفته2783-08107120180522Crack Propagation in nanocrystalline Iron-Nitrogen via Molecular Dynamics Simulationبررسی اشاعه ترک در نانوکریستال آهن- نیتروژن به روش شبیهسازی دینامیک مولکولی65749168210.30501/jamt.2018.91682FAرقیه محمدزادهدانشگاه شهید مدنی آذربایجان، مهندسی مواد، تبریز، ایراننیر رزم آرادانشگاه شهید مدنی آذربایجان، مهندسی مکانیک، تبریز، ایرانJournal Article20170514Recently, nitrogen alloyed steels have attracted the attention of researchers and industrial specialists due to their combination of strength and elongation. The identification of mechanical properties of nitrogen alloyed steels is very important for using these alloys with high reliability in various applications. Meanwhile, the resistance of material to crack propagation is one of the important parameters. Nowadays, nanoscience and computer simulations at nanoscale are noticed as the most studied subjects in the world. Molecular Dynamics Simulation (MDS) is one of the numerical methods at nanoscale which is the most deterministic method among available methods for the solution of molecular systems. The aim of this study is to simulate the crack propagation in Iron-Nitrogen nanocrystalline. In this regard, IronNitrogen nanocrystalline is modeled by applying Modified Embedded Atom Method (MEAM) interatomic potential using the related parameters for Iron-Nitrogen alloy. The microstructure of crack growth in nanocrystalline with dimension 100 40 3 A A A are investigated under tensile loading with velocity magnitude of 0.8 Å /ps at temperature of 300K. The results show that crack velocity increases with the increase in crack length. The increase in the peak of radial distribution function curve during different time steps is as a result of change in the positions of particles during crack propagation. Also, the results indicates that the magnitudes of stress at three crystal directions has firstly nonlinear behavior and then changes to linear one which is due to the change of direction of crack growth during simulation time steps. Also, the track-growth direction and the track opening are investigated under simulation conditions.در سال های اخیر فولادهای نیتروژن دار به دلیل داشتن خواص خوبی از استحکام و انعطاف پذیری مورد توجه محققان و متخصصان صنعتی قرار گرفته است. شناسایی خواص مکانیکی فولادهای نیتروژن دار به منظور استفاده از این آلیاژها با قابلیت اطمینان باال در تجهیزات مختلف از اهمیت بالایی برخوردار است. در این میان توانایی مقاومت ماده در برابر اشاعه ترک، از پارامترهای مهم به شمار می رود. هدف از این پژوهش، شبیه سازی اشاعه ترک در نانوکریستال آلیاژی آهن-نیتروژن می باشد. امروزه علوم نانو و شبیه سازی های رایانه ای در مقیاس مولکولی، به یکی از پرطرفدارترین موضوع های مورد مطالعه در دنیا مبدل شده است. یکی از روشهای عددی در ابعاد نانومتری، روش شبیه سازی دینامیک مولکولی است، که معین ترین روشِ حل سیستم های مولکولی از بین روش های موجود است. در تحقیق حاضر، سیستم کریستالی آهن-نیتروژن با اعمال تابع پتانسیل تصحیح شده اتم محاط شده MEAM و پارامترهای مربوط به آلیاژ آهن-نیتروژن شبیه سازی می شود. ریزساختار و همچنین مسیر رشد ترک در نانوکریستال مورد مطالعه، تحت بارگذاری کششی با مقدار سرعت ps /Å 8.0 در دمای 300K مورد بررسی و تحلیل قرار می گیرد. نتایج نشان می دهد که با افزایش کرنش و در نتیجه ایجاد تنش در نمونه ها، تغییر شکل پالستیک از نوک ترک به دلیل ایجاد تمرکز تنش در آن شروع می گردد. با افزایش بیشتر تنش حفره هایی در ساختار جوانه زده و به سمت ناحیه پیشروی رشد ترک اولیه اشاعه پیدا می کند. سرعت رشد ترک با افزایش طول ترک افزایش می یابد مقادیر تنش در هر سه جهت کریستالی ابتدا دارای رفتار غیرخطی و سپس رفتار خطی می باشند که ناشی از تغییر جهت رشد ترک در طول زمان شبیه سازی می باشد.https://www.jamt.ir/article_91682_6dfc73aa5141f1263d1c15442e2c1406.pdf