@article { author = {Raiesi Goojani, Payam and Alizadeh, Mostafa and Shayegh Boroujeny, Behrooz}, title = {Evaluation the Effect of Strain on Mechanical Behavior and Electrochemical Corrosion Properties of Al-2024 Alloy after Two-Step Aging and Thermomechanical Treatments}, journal = {Journal of Advanced Materials and Technologies}, volume = {8}, number = {2}, pages = {33-41}, year = {2019}, publisher = {Materials and Research Center (MERC)}, issn = {2783-0810}, eissn = {2783-0829}, doi = {10.30501/jamt.2019.94160}, abstract = {In this study, the effect of strainin thermomechanical two-step aging heat treatment on mechanical properties and electrochemical corrosion resistance of Al-2024 alloy has been investigated. These results were compared with normal aging T6. For this research, samples of Al-2024 alloys were placed at ambient temperature during normal aging under different percentages of strain, and then aging treatment was completed. Four strains of 10%, 30%, 50% and 65% were applied on the samples by rolling machine. The results of tensile test with low strain rate, potentiodynamic polarization curves and optical microscopy indicated that the sample with 50% strain offered optimum combination of microstructure, mechanical strength and corrosion resistance. This is due to the fine and uniform distribution of precipitates that cause increasing of yield strength, tensile strength and corrosion resistance by 27%, 10%, and 83%, respectively, in comparison with T6 heat treated[MP2D1] . Therefore applying strain of 50%, can increase the corrosion resistance with maintaining high strength in two-step aging and thermomechanical heat treatments.  }, keywords = {Aging Thermomechanical,Electrochemical Corrosion,polarization,Aluminum 2024 alloy}, title_fa = {بررسی تأثیر کرنش بر رفتار مکانیکی و خوردگی الکتروشیمیایی آلیاژ آلومینیوم 2024 بعد از عملیات پیرسازی ترمومکانیکی دومرحله‌ای}, abstract_fa = {پژوهش حاضر به بررسی تأثیر کرنش بر خواص مکانیکی و مقاومت به خوردگی الکتروشیمیایی آلیاژ آلومینیوم 2024 و مقایسه ­ی آن با پیرسازی معمولی T6 در فرایند عملیات حرارتی پیرسازی ترمومکانیکی دو مرحله­ ای پرداخته شده است. برای انجام این پژوهش نمونه­ هایی از این آلیاژ در حین پیرسازی معمولی تحت درصد­های مختلف کرنش در دمای محیط قرار گرفت و پس از آن عملیات پیرسازی کامل گردید. چهار کرنش 10%، 30%، 50% و 65% توسط دستگاه نورد بر نمونه ­ها اعمال گردید. نتایج حاصل از آزمایش کشش با نرخ کرنش پایین، منحنی­ های پلاریزاسیون پتانسیودینامیک و میکروسکوپی نوری نشان می­ دهد، نمونه ­ی با 50% کرنش در حالت بهینه ­ی ریزساختار، استحکام و مقاومت به خوردگی قرار دارد. این امر به دلیل توزیع ریز و یکنواخت رسوب­ ها است که باعث افزایش 27% در استحکام تسلیم، 10% در استحکام کششی و 83% در مقاومت به خوردگی، نسبت به عملیات حرارتی T6 شده است. بنابراین اعمال کرنش 50%، در عملیات حرارتی پیرسازی ترمومکانیکی دو مرحله­ ای فوق، می­تواند منجر به افزایش مقاومت به خوردگی با حفظ استحکام بالا شود.}, keywords_fa = {پیرسازی ترمومکانیکی,خوردگی الکتروشیمیایی,پلاریزاسیون,آلیاژ آلومینیوم 2024}, url = {https://www.jamt.ir/article_94160.html}, eprint = {https://www.jamt.ir/article_94160_685d54248ede3e56502f443434bc7315.pdf} }