@article { author = {Kebriyaei, Amir and Rahimipour, Mohammad Reza and Razavi, Mansour and Alizadeh Herfati, Atabak}, title = {Effect of Precursor Concentration on the Microstructure of Aluminum Oxide Coating Made through the Solution Precursor Plasma Spray Process}, journal = {Journal of Advanced Materials and Technologies}, volume = {11}, number = {1}, pages = {1-12}, year = {2022}, publisher = {Materials and Research Center (MERC)}, issn = {2783-0810}, eissn = {2783-0829}, doi = {10.30501/jamt.2021.264619.1147}, abstract = {In this research, the equipment required to produce ceramic coatings based on Solution Precursor Plasma Spray (SPPS) method was first identified and manufactured by exploring the relevant sources and contained information. Then, aluminum oxide coating was applied to the substrate with MCrAlY bond coat using the set-up. Further, a solution of aluminum sulphate with the concentrations of 0.5 and 1 molar was prepared and used as a precursor injected into the plasma plume in order to evaluate the effect of the precursor concentration on the coating microstructure. The results revealed that the alumina coating obtained from the more diluted precursor had a more porous structure than its counterpart, and its microstructure contained some bubble-like fractured shells as well as small spherical particles. However, the coating obtained from the precursor with higher concentration was found to be denser mainly due to the phenomenon occurring during the deposition through the SPPS process. The XRD analysis yielded similar results for both coatings where the α-Al2O3 was the predominant phase in the coating.}, keywords = {SPPS,Set Up,Alumina,Fractured Shells,precursor}, title_fa = {بررسی تأثیر غلظت پیش‌ماده بر ریزساختار پوشش اکسید آلومینیوم اعمال شده به روش پاشش پلاسما با پیش‌ماده محلول}, abstract_fa = {در این پژوهش، نخست با مطالعه منابع مربوطه و به‌کارگیری اطلاعات موجود در آن­ها، تجهیزات موردنیاز برای تولید پوشش سرامیکی به روش پاشش پلاسما با پیش­ماده محلول (SPPS)، شناسایی و ساخته شد. سپس اکسید آلومینیوم، روی سطح زیرلایه با پوشش میانی MCrAlY، با استفاده از تجهیزات ساخته ‌شده، پوشش‌دهی شد. به‌منظور بررسی تأثیر غلظت پیش ­ماده بر ریزساختار پوشش حاصل، از محلول سولفات آلومینیوم با غلظت ­های 5/0 و یک مولار، به‌عنوان پیش ­ماده تزریق‌شده به شعله پلاسما استفاده شد. نتایج نشان داد که پوشش آلومینای به­ دست‌آمده از پیش­ ماده رقیق­ تر، دارای ساختار متخلخل­ تری است و در ریزساختار آن، پوسته ­های شکسته ‌شده حبابی­ شکل به همراه برخی ذرات کروی کوچک مشاهده می ­شوند؛ اما پوشش حاصل از پیش ­ماده غلیظ ­تر، دارای تراکم بیشتری است که دلیل آن، به فرایندهای رخ­داده در حین رسوب­ دهی به روش SPPS مربوط است. نتایج آنالیز XRD برای هر دو پوشش، مشابه بود و فاز غالب در پوشش، α-Al2O3 تشخیص داده شد.}, keywords_fa = {SPPS,تجهیزات,آلومینا,پوسته‌های شکسته ‌شده,پیش‌ماده}, url = {https://www.jamt.ir/article_129292.html}, eprint = {https://www.jamt.ir/article_129292_c65e3a8747ad10f0aeddd6c7c1becfb7.pdf} }