پژوهشگاه مواد و انرژیمواد و فناوریهای پیشرفته2783-0810-32*20080722Sintering Behavior of Lithium Fluoride Pelletsرفتار تف جوشی قرص های لیتیم فلوراید1071147012910.30501/jamt.2010.70129FARafi Ali Rahimimaterials, nuclear arts and sciences research centerA. AhmadiCeramic, materials research school, NSTRIZohre Hamnabardmaterials, nuclear arts and sciences research centerM.R. ForoughiMaterials Engineering, Nuclear Arts and Sciences Research CenterJournal Article19700101In present work, sintering ability of LiF: Mg, Cu, P powders has been studied. At first, Samples were heat treated in different sintering temperatures and times. Then, bulk density and apparent porosity of specimens were measured by Archimedes' method. Finally, Micro structural analysis of sintered LiF samples was carried out with scanning electron microscopy (SEM). The results show that sintering behavior of LiF is very sensitive to temperature changes. Moreover, optimum sintering time of samples was long, which can be getting to more than 50 hours for some samples.مادة سرامیکی لیتیم فلوراید کاربردهای متنوعی در صنایع مختلف ازجمله صنایع سرامیک، اپتیک، متالوژی، تفرق اشعة ایکس و دزیمتری اشعة گاما و نوترون دارد. در این مقاله، قابلیت تف جوشی این ماده بررسی شده است. ابتدا نمونه ها در دماهای مختلف پخت شدند. سپس ویژگی های مختلف ازجمله چگالی کلی، تخلخل ظاهری، اندازه گیری و بررسی های ریزساختاری برای تحلیل نتایج انجام شد. نتایج این کار حساسیت بالای این سرامیک را نسبت به دمای تف جوشی نشان داد. همچنین زمان لازم برای تف جوشی این نوع سرامیک ها نسبت به سایر مواد سرامیکی بسیار بیشتر و درمورد برخی نمونه ها به 50 ساعت می رسد.پژوهشگاه مواد و انرژیمواد و فناوریهای پیشرفته2783-0810-32*20080722Recycling of Deformed Powder from Submerge Arc Welding (SAW)بازیافت خاکه حاصل از مصرف پودر جوشکاری زیرپودری1151277013010.30501/jamt.2010.70130FAK. ArzaniScience and research univercity, Azad univercityM. ShakeriS. K. SaidNejadJournal Article19700101Besides possessing proper technical properties, the materials used by modern technology should be economical and environment friendly. Human of the modern age is trying to find proper solutions to recycle a major part of he industrial wastes Instead of disposing them into rivers, seas and oceans or accumulating them on the uninhabited deserts of the third World countries. SAW wastes are also considered as a class of environmental pollutants. The present research aims at finding a method for recycling such wastes by making use of Phases assessment systems, such as XRD, XRF, SEM, and carbon-sulfur assessment system (Strolein system) and by using separation, formulation, and ceramic sintering. The results of the study show that the deformed powder from SAW process might be recycled and used as powder of SAW for welding of low-carbon steel (st37) by separating the iron particles and adding some additives to deformed waste powder.�(XRD)، فلورسانس پرتو ایکس (XRF)، بررسی نوع و شکل فازها، میکروسکوپ الکترونی� روبشی (SEM، EDX)، آنالیز مقدار کربن و گوگرد (دستگاه اشترولاین) و بااستفاده از روش های خردکردن، جداسازی، فرآوری، مخلوط سازی و زینتر سرامیکی، روشی برای مصرف مجدد خاکة حاصل از مصرف پودر جوشکاری زیرپودری یافت شود. طی این تحقیق مشخص شد که با جداسازی ذرات آهنی افزوده شده به ترکیب خاکه می توان از زبالة تولید شده دوباره برای ساخت پودر جوشکاری زیرپودری استفاده کرد.پژوهشگاه مواد و انرژیمواد و فناوریهای پیشرفته2783-0810-32*20080722Role of Plants Rumex Pulcher and Verbascum Songaricum in Accumulation of some Heavy Metals in Sarcheshmeh Copper Mine, Iranنقش دو گونة گیاهیRumex Pulcher و Verbascum Songaricum در جذب برخی عناصر سنگین در مناطق اطراف معدن مس سرچشمه1291367013110.30501/jamt.2010.70131FAS. Azad ShahrakiBiology, Shahid Bahonar UniversityA. AhmadimoghadamBiology, Shahid Bahonar UniversityF. NaseriInternational Center for Science, , Hight Technology of KermanE. EsmailzadehMechanical Engineering, Sharif University of TechnologyJournal Article19700101Sarcheshmeh copper mine, is located in south-west of Kerman, is one of a large open mine in the world and is one the important mineral and industrial site of Iran. The soil of the area naturally contains some heavy metals. Mining activities has also caused accumulation of polluting metals into the soil. Different methods are applied to reduce water and soil pollutants. Most of the methods are expensive and time consuming. Using suitable plants for remediation of the polluted soils, which is because of low cost and minimum environmental hazardous effects has accelerated in recent years. In this study, plants Rumex pulcher and Verbascum songaricum were collected from three sites around the Sarcheshmeh copper mine, and plant roots, shoots and the soils of the rhizosphere were analyzed for Cu, Zn and Pb in spring and summer 2007. The plant and soil samples were sent to Amdel laboratory in Australia were analyses for their metals contents using ICP. The results showed higher ranges of metals in sites accumulated in plants. Accumulation of these metals of plants in summer was more than spring. According to results it is indicated that the plants have high potential of accumulating of these metals.معدن مس سرچشمه در جنوب غرب کرمان یکی از معادن روباز بزرگ جهان و یکی از قطب های مهم معدنی و صنعتی کشور است. خاک این منطقه به طور طبیعی و همچنین دراثر فعالیتهای معدنی حاوی فلزات سنگین است. درحال حاضر روش?های متنوعی برای کاهش آلودگی خاک به کارمی رود. بیشتر این روش?ها زمان بر و پر هزینه اند. استفاده از گیاهان مناسب برای آلایش زدایی خاک های آلوده به این فلزات به علت قیمت پایین و کم کردن تخریب های زیست محیطی در دهه های اخیر بیشتر مورد توجه است. از این رو دو گونة گیاهی Rumex pulcher و Verbascum Songaricum برای تعیین جذبی عناصر مس، روی و سرب آزمایش شده3اند. نمونه برداری از ریشه، بخش هوایی گیاه و خاک اطراف ریشه در بهار و تابستان 1386 در سه ایستگاه انجام شد. نمونه های برداشت شده پس از آماده سازی در آزمایشگاه امدل استرالیا با روش بدون خاکسترسازی و بااستفاده از دستگاه ICP آنالیز شد. نتایج جذب فراوانی از عناصر فوق را در هر دو گیاه نشان می دهد. همچنین جذب اغلب عناصر در فصل تابستان بیشتر از فصل بهار بوده است. به طورکلی این گیاهان پتانسیل خوبی در جذب عناصر فوق و پالایش خاک از خود نشان دادند.پژوهشگاه مواد و انرژیمواد و فناوریهای پیشرفته2783-0810-32*20080722Effect of Cryotreatment on Microstructure and Wear Properties of Cold Work Tool D6 Steelاثر عملیات برودتی برروی ریزساختار و خواص سایشی فولاد سردکارD61371527013210.30501/jamt.2010.70132FAA. HabibollahzadehMaterials Engineering, Semnan University0000-0002-3128-3862Abbas Honarbakhsh RaoufEngineering, Semnan UniversityS. Pirhadi TavandashtJournal Article19700101Effect of cryogenic treatment on microstructure, hardness, and wear resistance of high Cr-C tool (D6) steel has been studied, in comparison with effect of conventional quench-temper treatments on those properties. Cryotreatment includes austenitizing, quenching in hot oil, immediate cooling of steel down to -78 or -180˚C, and keeping the samples at one of those temperatures for 6 or 24 hours. The results show that retained austenite decreases in microstructure and submicron carbides precipitate in matrix of steel after cryotreated samples, in relative to those after conventional quench-temper treatment. Wear resistance in cryotreated samples significantly increases in comparison of conventialy treated samples, however, hardness variation is moderate. Hardness and wear resistance increases as time and/or cooling increases during cryotreatment. It is revealed that increasing holding time in cryogenic environment from 6 to 24 hours improves wear resistance by 23%, however decreasing temperature of cryogenic environment from -78 to -180˚C provides only 4% improvement in wear resistance. Increasing velocity of wear disk increases wear resistance, whereas, increasing applied load decreases wear resistance of steel. In general, wear resistance of D6 steel after cryotreatment is significantly superior to those properties in D6 steel after conventional quench-temper treatment.�اثر عملیات برودتی برروی ریزساختار، سختی و مقاومت به سایش فولاد سردکار پُرکُرُم پُرکربن6 D درمقایسه با اثر عملیات تند سرمایش بازگشت بر این خواص مطالعه شده است. عملیات برودتی شامل مراحل آستنیته کردن، سردکردن سریع در روغن داغ، سرمایش سرُِیع فولاد تا دمای 78- یا ˚C180- و نگهداری نمونه ها در یکی از دو دمای مزبور به مدت 6 یا 24 ساعت است. نتایج نشان مُِی دهد که عملیات برودتی، درمقایسه با عملیات سردکردن سریع بازگشت مستمر، به کاهش آستنیت باقی مانده و نیز تشکیل کاربیدهای� ریز میکرونی در ساختار فولاد منجر می شود. مقاومت به سایش فولاد دراثر استفاده از عملیات برودتی، نسبت به عملیات حرارتی های مستمر، بسُِیار بهبود می یابد، درصورتی که تغییرات سختی ناشی از آن زُِیاد نیست. سختی و مقاومت به سایش فولاد با افزایش زمان یا دمای برودت درطی عملیات برودتی افزایش می یابد. مشخص شد که اثر افزایش زمان بیش از اثر افزایش برودت است؛ به نحوی که افزایش زمان از 6 به 24 ساعت مقاومت به سایش را به میزان 23 درصد بهبود می بخشد؛ ولی افزایش برودت از 78- به ˚C180- فقط 4 درصد بهبود در مقاومت به سایش اُِیجاد مُِی کند. افزایش سرعت چرخش دیسک ساینده درطی آزمون سایش، مقاومت به سایش را زُِیاد مُِی کند؛ ولی افزایش بار اعمالی این مقاومت را کاهش می دهد. به طورکلی، سختی و مقاومت به سایش فولاد 6 D پس از عملیات برودتی بسُِیار برتر از این خواص در همین فولاد پس از عملیات سردکردن سریع بازگشت مستمر است.پژوهشگاه مواد و انرژیمواد و فناوریهای پیشرفته2783-0810-32*20080722Study of Nano Particles Effects of Fe and Mn Compound in (La,Ce)(Pd,Co)O3 Perovskite Catalysts and its Comparison with Imported Catalyst of Iran Khodro with Nobel Metalsمطالعة اثر نانو ذرات ترکیبات آهن و منگنز در مبدل کاتالیستی O3(Pd,Co)(La,Ce) با ساختار پروسکایت و مقایسة آن با مبدل های کاتالیستی ایران خودرو به همراه فلزات گرانبها1531627013310.30501/jamt.2010.70133FAArsia KhanfekrIran university of science & technology (IUST), Science and research universityA. Nemati, Sharif University of Technology, Public univercityK. ArzaniScience and research univercity, Azad univercityM. HosseiniJournal Article19700101In this paper we work on prototype survey of using iron and manganese compounds in production of catalyst converter with nano particles for ROA dual fuel system instead of a lot of cerium in (La,Ce)(Pd,Co)O3-Perovskite catalysts and its comparison with imported catalyst of Iran Khodro with noble metals. (La,Ce)(Pd,Co)O3 Perovskite catalyst was prepared by the citrate route without use of Pt and Rh. We used just Pd (1.2 g) and it was deposited on ceramic monoliths according to a dip coating procedure. We used catalyst on RD car with XU7 motors model and measured the amount of emission with (AVL) test at Sapco Company and compared the catalyst with imported catalysts of Iran Khodro Company with noble metals such as Pd, Pt and Rh by Iran Khodro Company with Euro III standards. In conclusion Perovskite catalysts reduce emission better than imported catalysts, with lower emission and price. Monolite of catalysts were characterized by specific surface area measurements (BET) and X-ray diffraction (XRD) and X-ray fluorescence (XRF), and coat characterized by scanning electron microscopy (SEM). Finally the illustration shows Nano Particles size on coat.تحقیق حاضر استفاده از ترکیبات آهن و منگنز در ساخت مبدل کاتالیستی توسط نانوذرات برای خودروی روآ، به جای مقادیر زیاد سریم در مبدل کاتالیستی O3(Pd,Co)(La,Ce) با ساختار پروسکایت را بررسی می کند. در این پروژه با حذف فلزات گرانبهای پلاتین و رودیم و تنها بااستفاده از پالادیم، مبدل کاتالیستی O3(Pd,Co)(La,Ce) با فرآیند ساخت دستیابی به ساختار پروسکایت، برای خودرو دوگانه سوز روآ تهیه شد. پس از ساخت نمونه های اولیه در آزمایشگاه شرکت طراحی مهندسی و تهیة قطعات ایران خودرو (ساپکو) جایگزینی ترکیبات آهن و منگنز به جای مقادیر سریم بررسی شد تا کاتالیستی با درصد آلایندگی تقریباً مشابه کاتالیست های وارداتی ولی با قیمت کمتر تهیه گردد. انجام تست های میزان آلایندگی (AVL)، برروی مبدل های وارداتی همراه با فلزات گرانبها در شرکت ایران خودرو، نشان داد که کاتالیست های ساخته شده در حالت گازسوز، درصد آلایندگی بسیار کمتری دارند و میزان گازهای آلاینده NOx ،HC و CO بسیار کمتر است. کاتالیست های تهیه شده با نسبت بهینه ای از سریم، آهن و منگنز جانشین مناسبی برای کاهش بیش از 70% نیترات سریم مصرفی است، که بسیار ارزان تر از کاتالیست های وارداتی و با درصد آلایندگی کمتر است. برای بررسی خواص نمونه های ساخته شده، ریزساختاری تصویربرداری SEM برای بررسی شکل، توزیع و اندازة تخلخل ها وهمچنین آزمایش های BETبرای اندازه گیری سطح ویژه،XRF برای بررسی عناصر موجود و XRD برای بررسی فازها و ترکیبات موجود برروی نمونة مونولیت وارداتی (پایة مبدل کاتالیستی برای پوشش مواد) انجام شد. تصاویر SEM برای بررسی شکل، توزیع و اندازة تخلخل ها و ذرات تحلیل و بررسی شد.پژوهشگاه مواد و انرژیمواد و فناوریهای پیشرفته2783-0810-32*20080722Preparation and Characterization of Nanostructure Titania Colloidal Membranesساخت و بررسی خواص غشای کلوئیدی تیتانیای نانوساختار1631747013410.30501/jamt.2010.70134FAA. AlemMaterials Engineering, Iran University of Science and TechnologyJournal Article19700101In this investigation a nanostructure titania membrane on an alumina support was prepared. The support was made via a single axis press. The titania colloidal sol was then prepared. To have a crack-free titania membrane, PVA and HPC additives were included in the sol in specific amounts. The support was dipped in the sol and the layer was dried and calcined in a proper manner. The average particle size of the titania sol was measured to be 55.6 nm. X-ray diffraction technique was utilized to determine the titania phase transformation temperature. The burn out temperature of the volatile materials and the organic additives were determined via the TGA technique. Utilizing the XRD and TGA techniques the optimum calcinations temperature was determined to be 450˚C. Microstructure and the presence of any possible crack or defect were examined using Scanning Electron Microscopy. The final product was a crack-free titania membrane with no defect. Therefore, it can be concluded that the membrane preparation procedure is optimum.در این مقاله عوامل مؤثر بر ساخت و خواص غشای تیتانیایی برروی زیرپایة آلومینا بررسی شده� است. ابتدا زیرپایه با پرس تک محور ساخته و سپس سل کلوئیدی تیتانیا آماده شد. از افزودنی های پلی وینیل الکل (PVA) و هیدروکسی پروپیل سلولز (HPC) برای داشتن غشایی بدون ترک، در مقادیر خاصی در ساخت سل کلوئیدی تیتانیا استفاده شد. سپس، لایه نشانی تیتانیا برروی زیرپایة آلومینا به روش غوطه وری انجام شد و لایة تهیه شده، خشک و کلسینه شد. میانگین اندازة ذرات موجود در سل کلوئیدی بااستفاده از تکنیک تفرق پرتو لیزر، برابر nm6/55 اندازه گیری شد. به منظور ارزیابی دمای استحالة فازی در تیتانیا از پراش اشعة ایکس استفاده شد. تکنیک توزین حرارتی برای تعیین دمای خروج افزودنی های آلی و مواد فرار لایه به کار رفت. این نتایج به همراه نتایج آنالیز فازی تیتانیا، به انتخاب دمای بهینة کلسیناسیون لایه (C˚450) منجرشد. بررسی ریزساختاری غشایی به کمک میکروسکوپ� الکترونی روبشی، نشان می دهد ضخامت غشا برابر 570 نانومتر است. بررسی های بیشتر در این ضخامت نشان دهندة� غشایی بدون ترک با ریزساختاری همگن است. این امر نشان دهندة بهینه بودن شرایط ساخت غشااست.پژوهشگاه مواد و انرژیمواد و فناوریهای پیشرفته2783-0810-32*20080722Deposition and Determination of the Properties of Silicon Nitride Films in Argon and Nitrogen Atmospheresلایه نشانی و تعیین خواص نوری نیترید سیلیسیم در محیط های آرگن و نیتروژن1751827013510.30501/jamt.2010.70135FAN. ManavizadehElectrical Engineering, K. N. Toosi University of TechnologyA. KhodayariMechanical Engineering, K. N. Toosi University of TechnologyE. Asle SoleimaniElectrical Engineering, K. N. Toosi University of TechnologyJournal Article19700101Silicon nitride films were deposited on glass and polycrystalline silicon by RF sputtering using hot pressed ceramic Si3N4 target. Depositions were done in Argon and Nitrogen atmospheres. In order to optimize an antireflective coating for solar cells, sputtered silicon nitride thin films were grown with various RF power of deposition in two different atmospheres. The compositional, morphological and optical properties of film were investigated by RBS, SEM and UV/VIS/IR spectrophotometer analyses. Silicon nitride films (2000nm thickness) deposited with the RF power between 100-150W have exhibited high transparency≈92% for the spectral range between 300-1200nm. The silicon nitride antireflection coating deposited on the textured surface of multicrystalline silicon solar cells decreased the overall reflection of the cells from 12% to less than 2%.�لایه های نازک نیترید سیلیکون برروی زیرلایه بس کریستال سیلیکون و شیشه نازک بااستفاده از روش کندوپاش RF لایه نشانی شده اند. لایه نشانی یک بار در محیط گاز آرگن و بار دیگر در محیط گاز نیتروژن انجام شده� است. با تغییر توان لایه نشانی نسبت نیتروژن و سیلیکون موجود در لایه تغییرمی کند و لایه هایی با خواص نوری متفاوت به دست می آید. تأثیرات ناشی از تغییرات توان RF برروی خواص نوری و ترکیبات موجود در لایه ها بررسی شده است نسبت سیلیکون به نیتروژن در ترکیب پوشش های ضد بازتاب نیترید سیلیکون بهینه و به کمک آنالیز RBS بررسی شده است. از آنالیز UV/VIS/IR برای بررسی خواص نوری این لایه ها استفاده شده است. لایه های نیترید سیلیکونی که در محیط آرگن با ضخامت �2000 و با توان بین 100 تا 150 وات لایه نشانی شده اند، درصد عبور نور بسیار بالای 92% (درحدود شفافیت شیشه های نازک) در طیف وسیع 300 تا nm1200 دارند. لایه های ضد بازتاب نیترید سیلیکون مذکور بازتاب سطح سلول های بس کریستال سیلیکون را از 12% به کمتر از 2% کاهش می دهند.پژوهشگاه مواد و انرژیمواد و فناوریهای پیشرفته2783-0810-32*20080722Fabrication Ohmic Contact of Ni/Cu Structure on Polycrystalline Silicon Via Electrochemical Method used in Solar Cellsایجاد تماس اهمی ساختار Ni/Cu به روش الکتروشیمیایی برروی زیر لایه های پلی کریستال سیلیکون مورداستفاده در سلول های خورشیدی1831907013610.30501/jamt.2010.70136FAN. ManavizadehElectrical Engineering, K. N. Toosi University of TechnologyR. Safa IsiniElecterical and Computer Engineering, Tehran UniversityA. KhodayariMechanical Engineering, K. N. Toosi University of TechnologyE. Asle SoleimaniElectrical Engineering, K. N. Toosi University of TechnologyH. MalekiJournal Article19700101In this paper, a low-cost Ni/Cu structure as an ohmic contact was fabricated on Polycrystalline n+Si Via electrochemical method by the application of an ultrasonic system and the electrical resistivity of the contact was optimized. After electroplating of Ni in watts bath for 10, 20 and 40 min, an electroplated copper layer was deppsited on Ni film in order to reduce the sheet and contact resistance by using an ultrasonic system one can obtain a film with the lower surface roughness and the higher quality. The electrical resistivity of the electroplated Ni/Cu was investigated for vacuum annealing at various temperatures. Post treatments of the coated Ni improved the crystalline structure of the electroplated layer. Contact resistance of the Ni/Cu structure on an n+Si was measured using the Transmission Line Model (TLM) Method. An optimum specific contact resistance of 2.2×10-5 Ωcm2 was obtained for layers annealed at 400°C for 10 min. SEM, XRD, and EDX analyses were used to investigate the surface morphology, structure and composition of deposited films.در این مقاله، ساختار Ni/Cu به عنوان تماس اهمی برروی بس بلور سیلیکون به روش آبکاری الکتریکی و بااستفاده از دستگاه ماوراء صوت لایه نشانی شده و مقاومت الکتریکی آن بهینه شده است. نیکل بااستفاده از حمام وات برروی زیرلایة n+-Si در زمان های 10، 20 و 40 دقیقه لایه نشانی شده و برای کاهش مقاومت سطحی و تماس لایه ای از مس به روش آبکاری الکتریکی برروی لایة نیکل انجام شده است. آنالیزهای XRD، SEM و EDX برای بررسی ساختار بلوری، ساختار سطحی و عناصر تشکیل دهندة این لایه ها انجام شده و باتوجه به ناهمواری زیاد سطح زیرلایة پلی کریستال سیلیکون، درحین لایه نشانی از دستگاه ماوراء صوت برای ایجاد تماس های اهمی با چسبندگی بسیار خوب و کیفیت بالا استفاده شده است. پس از الگودهی نقاب موردنظر برای اندازه گیری مقاومت تماس از روش مدل خط انتقال (TLM) Transmission Line Model استفاده شده و مقاومت ویژة تماس برابر Ωcm25-10�2/2 به دست آمده است که مقاومت تماس مناسبی برای کاربرد در سلول های خورشیدی پلی کریستال� سیلیکون می باشد.پژوهشگاه مواد و انرژیمواد و فناوریهای پیشرفته2783-0810-32*20080722Exact Method in Design of Circular Base Plate under Large Eccentric Loadsروش جدید طراحی صفحه ستون دایره ای تحت بار با خروج از محوریت زیاد1912067013710.30501/jamt.2010.70137FAM. NaghipourCivil Engineering, Mazandaran University of Science and TechnologyM. DelvaraniCivil Engineering, Babol University of TechnologyN. Jafari MobinCivil Engineering, Babol University of TechnologyJournal Article19700101Circular base plates are commonly used for pipe columns, such as pylons in cabled-stayed bridges, lighting poles and electric power line posts. Against rectangular base plates, an exact method has not been presented about design of circular base plates in the classified and well-documented form. Therefore, this paper by expression of mathematic formulas describes on exact method to design these plates which use of this method requires an iteration approach to solve the equilibrium moment equation. Then it compares by presented graphs obtained designing results from exact and existing method [1], in return for different design parameters and demonstrates safe limits to use of approximate method. The results show that approximate method commonly will not be safe and can demonstrate reasonable results under specified conditions. Whereas exact method has been presented in this paper is safe and replies reasonably under any conditions.صفحه ستون های دایره ای بیشتر برای ستون های لوله ای شکل در پل های معلق کابلی، دکل های انتقال نیرو و تیرهای برق استفاده می شود. برخلاف صفحه ستون های مربع-مستطیلی، درزمینة طراحی صفحه ستون های دایره ای تاکنون روش دقیقی به صورت مدون و مستند ارائه نشده است. این مقاله با بیان روابط ریاضی، به تشریح روشی با دقت بالا جهت طراحی این صفحات پرداخته است که به کارگیری این روش مستلزم انجام فرایند تکرار سعی و خطا در حل معادلة تعادل لنگر است. سپس ازطریق نمودارهایی به مقایسة نتایج حاصل از طراحی به دو روش جدید و موجود [1] به ازای پارامترهای مختلف طراحی می پردازد و محدودة مورد اطمینان جهت به کارگیری روش تقریبی را ارائه می نماید. نتایج نشان می دهد که روش تقریبی همواره مورد اطمینان نیست و فقط در شرایطی خاص پاسخ های پذیرفتنی دارد. درحالی که روش جدید ارائه شده در این مقاله در هر شرایطی با اطمینان جوابگوست.پژوهشگاه مواد و انرژیمواد و فناوریهای پیشرفته2783-0810-32*20080722Effects of Nd: YAG Pulsed Laser Beam Parameters on Microstructure and Dimensions of Weld Pool for a Copper-Beryllium Plateبررسی تأثیر پارامترهای جوشکاری لیزر پالسی Nd:YAG بر روی ساختار انجمادی و ابعاد حوضچة مذاب در ورق نازک آلیاژ مس-برلیوم2072167013810.30501/jamt.2010.70138FAS. T. NiknejadMaterials Eng., Tehran UniversityS. A. A. Akbari MousaviMaterials Eng., Tehran UniversityJournal Article19700101The Nd:YAG pulsed laser welded structure of Copper-Beryllium alloy were studied by varying laser parameters such as pulse energy, spot diameter, duration and frequency. The metallographic results showed that the pulse energy should be kept as low as possible in order to obtain the weld pool with the highest values of penetration and the least width. Low pulse energy decreases the time for segregation of impurities. The impurities are the main cause of hot cracking. In addition, the laser spot diameter should be kept as low as possible. Moreover, the microscopic investigations demonstrate that the dendrite structure prevails in weld pool near the weld centerline and the cellular structure forms in weld pool near the base meal.�در این تحقیق، ساختار جوش لیزر پالسی Nd:YAG آلیاژ مس برلیوم˚C 17200، تحت تأثیر متغیرهای مختلف شامل انرژی پالس های لیزر، قطر کانونی اشعه، پهنای پالس و فرکانس در عمق و پهنای جوش بررسی شده است. نتایج به دست آمده نشان می دهد که به دلیل تفاوت در تحت تبرید ترکیبی در مناطق مختلف فلز مذاب، ساختار انجمادی شامل مورفولوژی های متعددی است. ساختار ستونی عمدتاً در منطقة مجاور مرز ذوب تشکیل می شود؛ درحالی که ساختار دندریتی و هم محور، ساختار غالب در نزدیکی خط مرکزی جوش به شمار می آید. تصویر میکروسکوپ الکترونی نشان می دهد که ذوب جزئی مرزدانه در منطقه تحت تأثیر حرارت روی داده است. تصاویر متالوگرافی نشان می دهد که افزایش بیش از اندازة ولتاژ پالس به تبخیر لایه سطحی آلیاژ و تقعر گرده جوش منجر می شود. برای ایجاد جوش با حداکثر عمق نفوذ و حداقل پهنا، کاهش قطر کانونی اشعه به جای افزایش انرژی پالس توصیه می شود. همچنین پهنای پالس، اثر دوگانه ای بر ابعاد حوضچة مذاب ایجادشده دارد.