@article { author = {Kaflou, Ali and Zahraee, Seyed Mohammad}, title = {The Effect of Adding Sn Powder to ST316L Powder on Sinter Ability and Microstructure of Steel Filters}, journal = {Journal of Advanced Materials and Technologies}, volume = {8}, number = {4}, pages = {31-37}, year = {2020}, publisher = {Materials and Research Center (MERC)}, issn = {2783-0810}, eissn = {2783-0829}, doi = {10.30501/jamt.2020.95827}, abstract = {In this study, porous samples of 316L were prepared by aqueous atomizing during powder metallurgyprocess. Pure 316L powder, as well as mixed with a certain percentage of Sn powder has been used to prepare the testspecimens, Then, by spraying zinc stearate as a lubricant on the mold surfaces and punches, the mixtures were pressedinto a rigid mold at four different pressures of 300, 350, 400 and 450 MPa. The green bulk were sintered in vacuumatmosphere at 1320 ° C for 60 min. The samples were cooled in the furnace and their densities were measured and thenmicrostructural and chemical analysis was performed by light microscopy and scanning electron microscopy.Measuring the density of the sintered samples showed that the porosity of the samples was from 38% to 46%)}, keywords = {Filter,Steel Filters,Porous Parts}, title_fa = {بررسی تاثیر افزودن پودر قلع به پودر فولاد ST316L در قابلیت تف جوشی و ریز ساختار فیلترهای فولادی}, abstract_fa = {از جمله استفاده فرآیند متالورژی پودر، ساخت فیلترهای فلزی و نیز فیلترهای فولادی است و همانطور که از نامشان پیداست این قطعات متخلخل هستند. فیلترها در حوزه های مختلف صنایع متالورژی، شیمیایی، داروسازی، فضائی و هوائی کاربرد و مورد استفاده وسیع قرار دارند. در این تحقیق، نمونه هائی متخلخل از پودر فولاد 316L تهیه شده بروش اتمایزینگ آبی طی فرآیند متالورژی پودر تهیه شدند. ابتدا پودرهای فولاد 316L بصورت خالص و همچنین با افزودن در صدی معین پودر قلع (sn) به پودر فولادی مخلوط شده و پس از استفاده از اسپری روانکار ( استئارات روی) و اسپری نمودن روی سطوح قالب و سنبه ها، مخلوط های حاصله در قالبی صلب و در چهار فشار مختلف 300 ، 350 ، 400 و 450 مگا پاسکال فشرده شدند. خشته های خام بدست آمده در آتمسفر خلاء در دمای 1320 درجه سانتیگراد به مدت 60 دقیقه سینتر شدند. پس از سرد شدن کوره و خارج نمودن نمونه ها، چگالی آنها اندازه گیری و سپس مورد بررسی های ریزساختاری و آنالیز شیمی توسط میکروسکوپ نوری و میکروسکوپ روبشی الکترونی قرار گرفتند. با اندازه گیری چگالی نمونه های سینتر شده ملاحظه گردید که تخلخل نمونه ها از 46 تا 38 درصد متغیر می باشد.}, keywords_fa = {فیلتر,فیلتری های فولادی,قطعات متخلخل}, url = {https://www.jamt.ir/article_95827.html}, eprint = {https://www.jamt.ir/article_95827_2c6e9ab2d50112b35b3131dd73ee2f1a.pdf} }