@article { author = {Akbarpour, Sotudeh and Karbasi, Saeed}, title = {Evaluation of Physical and Mechanical Properties of Hydroxyapatite/Titanium dioxide Composite Scaffold for Tissue Engineering Applications}, journal = {Journal of Advanced Materials and Technologies}, volume = {3}, number = {3}, pages = {17-26}, year = {2014}, publisher = {Materials and Research Center (MERC)}, issn = {2783-0810}, eissn = {2783-0829}, doi = {10.30501/jamt.2635.70268}, abstract = {In this study, firstly hydroxyapatite powder using natural method and bovine bone was synthesized at temperature of 900 ° C. Then it was synthesized reproducibiliby from foam ceramic scaffolds with 0, 3, 6 and 9 wt% and 50 wt% titania hydroxyapatite wet grinding method (slurry). In order to detect the changes of phase and chemical bonds was used diffraction of X-rays and infrared light spectroscopy. Microstructure and morphology of the nano composites was examined by scanning electron microscopy. According to the results, the volume fraction of porosities were obtained about 80-85%. The compressive strength was measured 0.14 to 1.321 MPa .Results indicate that the best type of scaffold physical properties such as porosity and shrinkage after sintering about low percentages of titanium dioxide, the 3 and mechanical properties suitable, the high percentage of titanium dioxide is the 6 percent.}, keywords = {Scaffold,Hydroxyapatite,Titanium dioxide,Composite,Tissue engineering}, title_fa = {ارزیابی خواص فیزیکی و مکانیکی داربست سرامیکی متخلخل کامپوزیتی نانو هیدرکسی آپاتیت/ دی اکسید تیتانیوم برای کاربردهای مهندسی بافت}, abstract_fa = {دراین پژوهش پودر هیدرکسی آپاتیت به روش طبیعی و با استفاده از استخوان گوساله در دمای C 900 تهیه گردید. سپس داربست سرامیکی به روش تکرارپذیری فوم پلی یورتان و با 0، 3، 6 و 9 درصد وزنی تیتانیا و 50 درصد وزنی هیدروکسی آپاتیت به روش آسیاب تر(دوغابی) سنتز شد. به منظور شناسایی تحولات فازی انجام شده و شناسایی پیوندهای شیمیایی ایجاد شده ازآنالیز پراش پرتوایکس و طیف سنجی پرتو فروسرخ استفاده شد. ریزساختار و مورفولوژی پودرنانوکامپوزیتی توسط مطالعات میکروسکوپ الکترونی روبشی مورد بررسی قرارگرفت. درصد تخلخل حدود 80-85 درصد اندازه گیری شد. استحکام فشاری اندازه گیری شده 14/0 تا 321/1 مگاپاسکال گزارش شد. نتایج نشان می دهد بهترین نوع داربست از نظر خواص فیزیکی از قبیل درصد تخلخل و انقباض بعداز پخت مربوط به درصدهای پایین دی اکسید تیتانیوم یعنی 3 و خواص مکانیکی مناسب مربوط به درصدهای 6 و 9 درصد TiO2 می باشد. در پایان داربست بهینه از نظر درصد تخلخل، خواص مکانیکی و ریزساختار، داربست با 6 درصد TiO2 و 50 درصد HA انتخاب گردید.}, keywords_fa = {داربست,هیدروکسی آپاتیت,دی اکسیدتیتانیوم,کامپوزیت,مهندسی بافت}, url = {https://www.jamt.ir/article_70268.html}, eprint = {https://www.jamt.ir/article_70268_392923ae25f3c5698d2313b2a05dbb6f.pdf} }