@article { author = {Esmaili, Hasan and Sheibani, Saeed and Rashchi, Fereshteh}, title = {Kinetic Study on the Effect of PH in the Photocatalytic Degradation of Methylene Blue With Fe-FeS Nanocomposite Powder}, journal = {Journal of Advanced Materials and Technologies}, volume = {6}, number = {3}, pages = {1-8}, year = {2017}, publisher = {Materials and Research Center (MERC)}, issn = {2783-0810}, eissn = {2783-0829}, doi = {10.30501/jamt.2017.70367}, abstract = { In this paper, photocatalytic activity of mechanothermally synthesized Fe-39%FeS nanostructuredcomposite powder is investigated. Fe and S powders mixture with atomic ratio of 2:1 (Fe:S) is mechanically activatedand then heat treated at 850◦C for 2 h. X-ray diffraction (XRD), Field Emission Scanning Electron Microscopy(FESEM) and UV-vis spectroscopy are applied for characterization of composite powder. XRD results are shown thatFe-FeS powder was synthesized successfully. FESEM images showed that powder with the size of less than 2 μm isformed after heat treatment. Also, the effect of pH as an effective factor is investigated. It can be seen that thedegradation efficiency in basic solution is higher than acidic and neutral solution. Dyes degradation reached to 91%after 195 min irradiation of visible light in pH=11. In addition, kinetic study showed that the photocatalytic dedradationis initially (0-75 min) followed by first order model and after that the mechanism is possibly changed to the secondorder model. }, keywords = {photocatalyst,Composite,Nanostructure,Fe-FeS,Kinetics,pH}, title_fa = {تحلیل سینتیکی تاثیر pH بر روی حذف فتوکاتالیستی رنگدانه متیلن بلو توسط پودر نانوکامپوزیتی Fe-FeS}, abstract_fa = {در این پژوهش، عملکرد فتوکاتالیستی پودرهای کامپوزیتی نانوساختار Fe-39 %FeS سنتز شده به روش مکانوترمال مورد بررسی قرار گرفت. ابتدا مخلوط پودری Fe و S با نسبت اتمی آهن به گوگرد برابر 1:2 تحت فعال‌سازی مکانیکی قرار گرفت و سپس به مدت دو ساعت در دمای 850 درجه‌ سانتی‌گراد عملیات حرارتی شد. به منظور مشخصه‌یابی پودر سنتز شده از آنالیزهای پراش پرتو ایکس (XRD)، میکروسکوپ الکترونی روبشی گسیل میدانی (FESEM) و طیف‌سنج مرئی – فرابنفش (UV-vis spectroscopy) بهره برده شد. نتایج XRD سنتز موفق ساختار کامپوزیتی Fe-FeS را نشان داد. تصاویر FESEM نیز ذرات پودری با اندازه کمتر از دو میکرون را پس از عملیات حرارتی نمایش می‌دهد. هم‌چنین در بررسی فتوکاتالیستی، تاثیر pH به عنوان عامل موثر بررسی شد. نتایج نشان داد که در محیط‌های بازی میزان تخریب متیلن بلو بیشتر از محیط‌های اسیدی و خنثی است که در مورد pH برابر 11 پس از تابش 195 دقیقه نور مرئی 91 درصد از متیلن بلو مورد تخریب قرار گرفت. علاوه بر این نتایج بررسی‌های سینتیکی نیز نشان داد که فرآیند تخریب فتوکاتالیستی در ابتدا (75-0 دقیقه) از مدل درجه اول پیروی ولی با گذشت زمان با تغییر سازوکار از مدل درجه دوم پیروی می‌کند.}, keywords_fa = {فتوکاتالیست,کامپوزیت,نانوساختار,Fe,Fes,سینتیک,pH}, url = {https://www.jamt.ir/article_70367.html}, eprint = {https://www.jamt.ir/article_70367_569c96a59077e53e78bcd9c0e5e237e9.pdf} } @article { author = {Kazemzad Asiabi, Mahmoud and Daryani Tabrizi, Mohammad and Sadati, Mustafa and Ebadzadeh, Touradj and Kaflou, Ali}, title = {Synthesis and Characterization of Cerium rich MmNi3.55Co0.75Mn0.4Al0.3 for Ni-MH battery applications}, journal = {Journal of Advanced Materials and Technologies}, volume = {6}, number = {3}, pages = {9-16}, year = {2017}, publisher = {Materials and Research Center (MERC)}, issn = {2783-0810}, eissn = {2783-0829}, doi = {10.30501/jamt.2017.70375}, abstract = {Li-Ion and Ni-MH batteries are the best candidate for Electric Vehicles. Despite higher energy densities of Li-Ion batteries, because of economical reason Ni-MH Batteries are still attractive for scientist. In this investigation Cerium rich MmNi3.55Co0.75Mn0.4Al0.3 has been produced via Vacuum Arc Remelting Process. Phase characterization has shown that the predominant crystallographic phase is Hexagonal type with AB5 chemical formulation. Volumetric Sievert test has shown that the alloy could store 1%wt percent hydrogen at room temperature. Electrochemical analysis with Evium-Stat has shown that the energy density which the alloy can reversibly deliver is about 150 mAh/g.}, keywords = {Nickel-Metal Hydride Battery,Hydrogen Storage Alloys,Mischmetal,Vacuum Arc Remelting}, title_fa = {بررسی ریزساختار و کیفیت ذخیره‌سازی هیدروژن در آلیاژ MmNi3.55Co0.75Mn0.4Al0.3 حاوی میش‌متالِ غنی از سریم، به منظور استفاده در باتری‌های نیکل- هیدرید فلزی}, abstract_fa = {امروزه باتری‌های لیتیومی و نیکل- هیدرید فلزی به دلیل ظرفیت ذخیره‌‌سازی بالاترِ انرژی و عدم به‌کارگیری فلزات سنگین و آلاینده محیط‌زیست، بسیار مورد توجه‌اند. در باتری‌های نیکل- هیدرید فلزی، آلیاژ جاذب هیدروژن در الکترودِ منفی با هیدرولیز آب به هیدرید فلز تبدیل می‌گردد. در پژوهشِ حاضر آلیاژ MmNi3.55Co0.75Mn0.4Al0.3 حاوی میش‌متالِ غنی از سریم، با استفاده از روش قوس الکتریکی تحت خلاء سنتز شد. در ادامه، آلیاژ حاصل جهت همگن‌سازی به مدت هفت ساعت در کوره تیوبی و در دمای 900 درجه سانتی‌گراد قرار گرفت. خردایش آلیاژ به دلیل ماهیت ترد آن در یک هاون عقیق انجام شد و آلیاژ خرد شده با اندازه ذراتِ کمتر از 50 میکرون تحت آزمون‌های اشعه ایکس(بررسی ریزساختارساختار)، سیورت (بررسی ظرفیت ذخیره‌سازی هیدروژن) و الکتروشیمی (بررسی میزان انرژی ذخیره شده به صورت برگشت‌پذیر) قرار گرفت. الگوی پراش اشعه ایکس نشان می‌دهد آلیاژ حاصل به‌طور عمده ساختار کریستالوگرافی هگزاگونال با فرمول شیمیایی AB5 دارد. بررسی‌های انجام شده به وسیله دستگاه سیورت نشان می‌دهد، در دمای محیط یک درصد وزنی و در دمای 60 درجه سانتیگراد 6/0 درصد وزنی هیدروژن توسط آلیاژ، قابل ذخیره‌سازی است. هم‌چنین بررسی‌های الکتروشیمیایی به وسیله دستگاه ایویوم (Evium) نیز نشان می‌دهد این آلیاژ به صورت برگشت‌پذیر قابلیت ذخیره‌سازی انرژی به میزان mAh/g 150 را دارد.}, keywords_fa = {باتری نیکل,هیدرید فلزی,آلیاژ جاذب هیدروژن,میش‌متال,ذخیره‌سازی انرژی,قوس الکتریکی تحت خلاء}, url = {https://www.jamt.ir/article_70375.html}, eprint = {https://www.jamt.ir/article_70375_68de7d53727efc6ac884c8a723419bdc.pdf} } @article { author = {Gholampour, Mahdi and Movassagh-Alanagh, Farid and Salimkhani, Hamed}, title = {Synthesis of the Microwave Absorber Fe3O4/CFs Nanocomposite Via Electrophoretic Deposition With a Wide Effective Absorption Bandwidth}, journal = {Journal of Advanced Materials and Technologies}, volume = {6}, number = {3}, pages = {17-26}, year = {2017}, publisher = {Materials and Research Center (MERC)}, issn = {2783-0810}, eissn = {2783-0829}, doi = {10.30501/jamt.2017.70368}, abstract = { In this study, the structural, magnetic and microwave absorption properties of a microwave absorbercomposite fabricated through electrophoretic deposition (EPD) of Fe3O4 nano-particles on carbon fibers (CFs) werestudied. Firstly, co-precipitation method was employed to synthesize the Fe3O4 nano-particles. Then, these assynthesized Fe3O4 nano-particles were successfully deposited on CFs using a modified EPD process. The measuredmagnetic properties of the as-synthesized Fe3O4 nano-powder and the Fe3O4/CFs nano-composite showed that thesaturation magnetization of the bare Fe3O4 was decreased from 72.3 to 33.1 emu/g for the Fe3O4/CFs nano-compositeand also its corecivity was increased from 4.9 to 168 Oe for the nano-composite. The results of reflection loss (RL)measurements in the 8.2- 12.4 GHz frequency range indicated that the RL of Fe3O4/CFs nano-composites aresignificantly influenced by their thickness. The maximum RL value of -10.2 dB at 10 GHz with an effective absorptionbandwidth about 2 GHz was obtained for the sample with the thickness of 2 mm }, keywords = {Carbon Fibers,Microwave absorption,nano-composite,Fe3O4 nano-particles}, title_fa = {ساخت نانوکامپوزیت ذرات مگنتیت/الیاف کربنی به روش رسوبدهی الکتروفورتیک به عنوان جاذب امواج مایکروویو با باند بسامدی جذب موثر پهن}, abstract_fa = { در این تحقیق به بررسی خواص ساختاری، مغناطیسی و جذب امواج مایکروویو نانوکامپوزیت های جاذب ساخته شده از طریـق پوشـش دهـی الیـافکربنی ) (CFsبا نانوذرات مگنتیت ) (Fe3O4نوسط رسوب دهی الکتروفورتیک ) (EPDبهبود یافته، پرداخته شده است. ابتدا نانوذرات مگنتیـت بـه روش هـم رسـوبیتهیه شده و سپس به وسیله ی فرآیند رسوب دهی الکتروفورتیک بهبود یافته روی CFsپوشش داده شد. بررسی خواص مغناطیسی نشان داد کـه مقـادیر مغنـاطشاشباع و وادارندگی نانوپودر مگنتیت پس از انجام فرآیند رسوب دهی الکتروفورتیک به ترتیـب از 72,3بـه 33,1 emu/g از 4,9بـه 168 Oe بـرای نانوکامپوزیـتمگنتیت/الیاف کربنی می رسد. نتایج آزمون جذب امواج مایکروویو در محدوده ی بسـامدی 8,2تـا 12,4 GHzنشـان داد کـه میـزان جـذب مـوج نانوکامپوزیـتمگنتیت/الیاف کربنی به شدت به ضخامت آن بستگی دارد. مقدار بیشینه ی جذب موجی در حدود -10,2 dBدر 10 GHzبا پهنای باند جـذب مـوثری در حـدود2 GHzبرای نمونه ی با ضخامت 2 میلیمتر به دست آمد }, keywords_fa = {الیاف کربنی,جذب امواج مایکروویو,نانوکامپوزیت,نانوذرات مگنتیت}, url = {https://www.jamt.ir/article_70368.html}, eprint = {https://www.jamt.ir/article_70368_fada8f984a056a8186735dfa03550207.pdf} } @article { author = {Majidian, Hudsa and Ghaffari Ghods, Somayeh and Ebadzadeh, Touradj}, title = {Slip Casting of Alumina-Fe Composite Under Magnetic Field}, journal = {Journal of Advanced Materials and Technologies}, volume = {6}, number = {3}, pages = {27-39}, year = {2017}, publisher = {Materials and Research Center (MERC)}, issn = {2783-0810}, eissn = {2783-0829}, doi = {10.30501/jamt.2017.70369}, abstract = {In this study, alumina-iron composites have been prepared by slip casting in order to provide gradient iron in alumina. 5 wt.% of iron was used under the magnetic fields by the magnitude of 0.8 and 0.08T. Two dispersants were examined as the dispersing agent using 70, 75 and 80 wt.% of solid loading in slips. Samples were sintered in a microwave oven at the temperature of 1350˚C and 1450˚C for 30 minutes, at 1500˚C for 1 minute, and in a conventional tube oven at the temperature of 1485˚C for 2 hours using argon gas. The apparent and optical microscope pictures of green and sintered samples revealed that using PCN and 70 wt.% of solid loading under the mild magnetic field results in the best sample regard as density (3.7 g/cm3 ), strength (82.7 MPa) and iron gradient.}, keywords = {Alumina-Fe composite,Slip casting,Magnetic field,Gradient}, title_fa = {ریخته گری دوغابی مخلوط پودرهای آلومینا-آهن تحت میدان مغناطیسی}, abstract_fa = {در این پژوهش کامپوزیت­ های آلومینا-آهن به منظور ایجاد گرادیان ذرات آهن در زمینه آلومینا به روش ریخته ­گری دوغابی تهیه شد. مقدار آهن 5% وزنی انتخاب و برای ایجاد گرادیان از دو میدان مغناطیسی با بزرگی 8/0 و 08/0 تسلا استفاده شد. دوغاب­ ها با 70، 75 و 80 درصد وزنی ماده جامد و دو پراکنده­ ساز (دیسپرزنت) تهیه و تأثیر آنها بر ایجاد گرادیان آهن بررسی شد. نمونه­ ها در کوره مایکروویو به مدت 30 دقیقه در دماهای C˚1350 و C˚1450 و در دمای C˚1500 به مدت یک دقیقه در آرگون سینتر شدند. برخی از نمونه ­ها نیز در دمای 1485 درجه سانتی­گراد به مدت دو ساعت در کوره تیوبی در آرگون سینتر شدند. نتایج تصاویر ظاهر نمونه ­ها و میکروسکوپ نوری از گرادیان آهن در نمونه­ های خام و سینتر شده نشان داد که استفاده از دیسپرزنت PCN با 70% ماده جامد تحت میدان مغناطیسی 08/0 تسلا بهترین نمونه از نظر توزیع آهن، چگالی (g/cm3 7/3) و استحکام (MPa 7/82) می ­باشد.}, keywords_fa = {کامپوزیت آلومینا - آهن,ریخته‌گری دوغابی,میدان مغناطیسی,گرادیان}, url = {https://www.jamt.ir/article_70369.html}, eprint = {https://www.jamt.ir/article_70369_930268c393682eee2a2ffb5969afe0c4.pdf} } @article { author = {Nasiri, Zeynab and Mashhadi, Mehri}, title = {Investigation on Microstructure, Mechanical Properties and Pressureless Sintering Behavior of ZrB2-SiCnano/micron Composites Toughened by AlN}, journal = {Journal of Advanced Materials and Technologies}, volume = {6}, number = {3}, pages = {41-50}, year = {2017}, publisher = {Materials and Research Center (MERC)}, issn = {2783-0810}, eissn = {2783-0829}, doi = {10.30501/jamt.2017.70370}, abstract = { In the present paper, ZrB2-SiC nanocomposite was developed by pressureless sintering method. Microsized AlN powder and SiC powderes at nano and micro-sized scale were used as additive. In order to producecomposite samples, the primary powders were milled and blended in planetary ball mill apparatus with rotational speedof 200rpm and then processed using hot pressing (80ᵒC and 100MPa), cold isostatic press and sintering at 2150ᵒC. Thevalues of relative density and porosity of samples were measured to evaluate the effect of presence of micro-sized SiCand SiC nano particles simultaneously on the pressureless sintering behavior of ZrB2-SiC. In order to compare themicrostructure and mechanical properties of samples Scanning Electron microscopy (SEM), equipped with EDSspectroscopy, XRD analysis, hardness and toughness tests were used. The results show that as the volume percentage ofnano SiC decreases to 15 vol.% and AlN increases to 7.5 vol.% the hardness (17.1 GPa), toughness (5.7 MPa.m1/2) andrelative density (98.1%) increase. }, keywords = {Ultra high temperature ceramics,ZrB2-SiCnano/micron composites,Pressureless sintering,Mechanical properties}, title_fa = {بررسی تأثیر همزمان ذرات SiC نانو و میکرون بر استحکام خمشی و رفتار سینتر بدون فشار کامپوزیت بر پایه دیبورید زیرکونیم (ZrB2 (تقویتشده با نیترید آلومینیوم (AlN)}, abstract_fa = { در این تحقیق، نانوکامپوزیت ZrB2-SiCبه روش سینتر بدون فشار تولید گردید. از پودر AlN در مقیاس میکرون به عنوان افزودنی اسـتفاده شـد. بـه منظور بررسی تأثیر حضور همزمان ذرات SiC نانو و میکرون ابتدا پودر ZrB2به همراه درصدهای مختلف از SiC نانو و میکرون در آسیاب سیارهای با به مـدت دو ساعت با سرعت 200rpm آسیاب شدند. مخلوط حاصل پس از پرس گرم اولیه در دمای 80oC و فشار 100MPa تحت فرآیند پرس ایزواستاتیک سرد (CIP) قرار گرفته و در دمای 2150 درجه سانتیگراد سینتر شد. به منظور تعیین نسبت بهینه SiC نانو به میکرون، چگالی نسبی، سختی و چقرمگی نمونه ها اندازه گیـری شد. سپس، ذرات AlN به کامپوزیت ZrB2-SiC اضافه شده و ریزساختار و خواص مکانیکی آن مورد بررسی قرار گرفت. نتایج حاصل شده از تمامی نمونه ها در ترکیبات مختلف نشان می دهند که با تغییر درصد حجمی SiC نانو از 20 درصد حجمی نانو به 15درصد نانو و پنج درصد میکرون، کاهش در تخلخل و افزایش در چگالی رخ می دهد. با بررسی ریزساختاری و اندازه گیری خواص مکانیکی نمونه ها بیشترین سختی و چقرمگی شکست نیز، در ترکیب دارای به ترتیـب 15 و 5 درصد حجمی SiC نانو و میکرون و با مقادیر 15/9Gpa و 4/9 Mpa.m1/2 مشاهده شد. با افزودن ذرات 7/5 درصـد حجمـی AlN چگـالی بـه 98/1 درصـد و مقادیر سختی و چقرمگی شکست به 17/1GPa و 5/7 Mpa.m1/2 افزایش یافت . }, keywords_fa = {نانوکامپوزیت,دیبورید زیرکونیم,کاربید سیلیسیم,نیترید آلومینیوم,سینتر بدون فشار}, url = {https://www.jamt.ir/article_70370.html}, eprint = {https://www.jamt.ir/article_70370_985ead8070b0ac518004a50a3b992ea2.pdf} } @article { author = {Ebrahimi, Izadyar and Besharati-Seidani, Abbas}, title = {Investigation of Using Nickel Based Conductive Coatings in the Radar Wave Absorbers With Salisbury Screen Structure}, journal = {Journal of Advanced Materials and Technologies}, volume = {6}, number = {3}, pages = {51-59}, year = {2017}, publisher = {Materials and Research Center (MERC)}, issn = {2783-0810}, eissn = {2783-0829}, doi = {10.30501/jamt.2017.70371}, abstract = { In this study, two- and three-dimensional polyester fabrics were coated with nickel via electroless platingmethod in order to produce X-band radar absorbing coatings. Morphology, thickness, coating composition, conductivityand radar absorption behavior of them were evaluated. After coating, the conduction of two- and three-dimensionalfabrics was increased to 0.023 and 0.0043 cm2/Ω, respectively. Checking the morphology of the coatings by scanningelectron microscopy showed that the nickel particles on the surface of fibers have the dome-shaped structures.Microstructure investigation of fabricated polyester coatings by X-ray spectral energy distribution showed that theamount of loaded nickel is 64.56%. The study of the radar absorption behavior of two- and three-dimensional coatingsshowed that the both of them can absorb more than 96.45% X-band radar waves (8-12 GHz). The investigation of thewashing, rubbing and light fastness of fabricated coatings showed that electroless plating method can fix nickel on thesurface of fibers well so that these coatings show high stability against these environmental factors. }, keywords = {Electroless plating,Conductive Fibers,nickel,Salisbury screen,RADAR}, title_fa = {بررسی کاربرد پوششهای رسانای پایه نیکل در جاذبهای امواج رادار با ساختار پرده سالیسبوری}, abstract_fa = { در این تحقیق، پوشش دهی پارچه های پلی استر دو بعدی و سه بعدی با پوشش نیکل به روش الکترولس به منظور تولیـد پوشـش هـای جـاذب امـواج راداری باند ایکس انجام گرفت. مورفولوژی، ضخامت پوشش، ترکیب شیمیایی پوشش، رسانایی و رفتار جذب امواج راداری آنها ارزیابی شد. با انجـام پوشـش دهی، رسانایی پارچه های دو بعدی و سه بعدی به ترتیب بـه 0/023 و 0/0043 سـانتیمتـر مربـع بـر اهـم افـزایش یافـت. بررسـی مورفولـوژی پوشـش توسـط میکروسکوپی الکترونی روبشی نشان داد که ذرات نیکل روی سطح الیاف دارای ساختارهای گنبدی شکل هستند. بررسی ریزساختاری پوشـش هـای پلـی اسـتری ساخته شده توسط توزیع انرژی طیفی اشعه ایکس نشان داد که مقدار نیکل بارگذاری شده %64/56 می باشد. مطالعه جذب امواج راداری پارچه های دو بعـدی و سه بعدی نشان داد هر دو آنها توانایی جذب بیش از 96/45 درصد امواج راداری باند ایکس (8-12گیگاهرتز) را دارند. ارزیابی ثبات های شستشویی، سایشـی و نوری پوششهای تهیه شده نشان داد که روش پوشش دهی الکترولس توانسته نیکل را به خوبی بر روی الیاف تثبیت کند به گونه ای که پارچه هـای رسـانای تولیـد شده مقاومت بالایی در برابر این عوامل محیطی از خود نشان می دهند.}, keywords_fa = {لایه نشانی الکترولس,الیاف رسانا,نیکل,پرده سالیسبوری,رادار}, url = {https://www.jamt.ir/article_70371.html}, eprint = {https://www.jamt.ir/article_70371_a518235fd773f6613be2e0be953c311e.pdf} } @article { author = {Karami, Razieh and Kazazi, Mahdi}, title = {Synthesis, Characterization and Electrochemical Performance of Nanostructured Cobalt Oxide and Nickel Cobalt Oxide Active Materials for Supercapacitors}, journal = {Journal of Advanced Materials and Technologies}, volume = {6}, number = {3}, pages = {61-68}, year = {2017}, publisher = {Materials and Research Center (MERC)}, issn = {2783-0810}, eissn = {2783-0829}, doi = {10.30501/jamt.2017.70372}, abstract = { In this research, nanostructured cobalt oxide and nickel cobalt oxide active materials were successfullysynthesized by a hydrothermal route. Structural characterizations of the prepared active materials were performed usingX-ray diffraction (XRD), field emission scanning electron microscopy (FESEM) and elemental analysis (EDS). Theresults of these experiments showed that nickel has been successfully doped in the cobalt oxide spinel structure. Also,the microscopic examination showed the nano-rod morphology for the cobalt oxide and nickel cobalt oxide, whichyields the high specific surface area for electrochemical reactions, leading to increase energy storage capacitance.Energy storage performance of the prepared active materials was investigated using electrochemical experiments ofcyclic voltammetry and galvanostatic charge-discharge in a solution of 6 M KOH in Swagelok standard cell. Thespecific capacitance of nickel containing cobalt oxide sample (1624 F g-1) was obtained higher than that of cobalt oxide(1020 F g-1) at a current density of 2 A g-1. }, keywords = {Supercapacitors,electrochemical performance,Hydrothermal method,Cobalt oxide,nickel-cobalt spinel}, title_fa = {ساخت، مشخصه یابی و عملکرد الکتروشیمیایی مواد فعال نانوساختار اکسید کبالت و اکسید نیکل کبالت مورد استفاده در ابرخازن ها}, abstract_fa = {در این پژوهش مواد فعال نانوساختار اکسید کبالت و اکسید نیکل کبالت به روش هیدروترمال به‌طورموفقیت‌آمیزی سنتز شدند. مشخصه‌یابی مواد فعال تهیه شده توسط پراش اشعه (XRD) X، میکروسکوپ الکترونی روبشی گسیل میدانی (FE-SEM) و آنالیز عنصری (EDS) انجام شد. نتایج آزمون مشخصه یابی نشان دادند که نیکل به صورت موفقیت‌آمیزی در داخل ساختار اسپینل اکسید کبالت قرار گرفته است. هم‌چنین بررسی‌های میکروسکوپی نشان‌دهنده مورفولوژی نانو‌میله‌ای اکسید کبالت و اکسید نیکل کبالت هستند، که سطح ویژه بالایی را به منظور واکنش‌های الکتروشیمیایی جهت افزایش ظرفیت ذخیره‌سازی انرژی در اختیار قرار می‌دهند. عملکرد ذخیره‌سازی انرژی ماده‌ی فعال تهیه شده به عنوان ماده فعال شبه‌ابرخازن‌ها توسط آزمون‌های الکتروشیمیایی ولتامتری چرخه‌ای و آزمون شارژ/ تخلیه جریان ثابت در محلول شش مولار KOH در سل استاندارد Swagelok مورد بررسی قرار گرفت. ظرفیت ویژه خازنی نمونه حاوی نیکل (F g-1 1624) بسیار بالاتر از ظرفیت اکسید کبالت (F g-1 1020) در چگالی جریان A g-1 2 به‌دست آمد.}, keywords_fa = {ابرخازن‌ها,عملکرد الکتروشیمیایی,روش هیدروترمال,اکسید کبالت,اسپینل نیکل کبالت}, url = {https://www.jamt.ir/article_70372.html}, eprint = {https://www.jamt.ir/article_70372_6c9777747244bfefb06e05affa928060.pdf} } @article { author = {Shayegh Boroujeny, Behrooz and Moolyanian, Majid and Raiesi Goojani, Payam and Ghashghayi, Mohammadreza}, title = {Investigation of the Effects of SIMA Process on Microstructure and Electrochemical Behavior of Zn Sacrificial Anode in Simulated Sea Water}, journal = {Journal of Advanced Materials and Technologies}, volume = {6}, number = {3}, pages = {69-77}, year = {2017}, publisher = {Materials and Research Center (MERC)}, issn = {2783-0810}, eissn = {2783-0829}, doi = {10.30501/jamt.2017.70373}, abstract = { Zinc and its alloys have been recognized as sacrificial anodes due to being widely used in cathodicprotection systems. Problems caused by the high vapor pressure of this metal in the process of melting and casting havecaused that reform processes of the microscopic structure in the solid state for zinc attract a lot of attention. Straininduced melt activation (SIMA) process is one of the semi-solid forming processes in the production of parts with nondendritic structure. In this study, the effect of SIMA process on microstructure and electrochemical behavior of zincsacrificial anode has been examined. The samples were placed under the strain rates of 20-50%, different temperaturesin the range of 425-435°C and time periods of 10-40 minutes. Optimal spherical microstructure was obtained in 50%cold work conditions, temperature of 430°C and 10 minutes. The results obtained from the polarization test and anodetest on the optimal spherical sample indicate a tangible reduction in electrochemical corrosion current density by 90%and a slight decrease in anode efficiency compared to the raw sample. Elemental analysis (EDX), metallography imagesand microhardness profile show the concentration of alloying elements on grain boundary and turning of uniformcorrosion into localized corrosion and thus reduced anode efficiency after SIMA process }, keywords = {Zinc sacrificial anode,SIMA process,Polarization Test,anode test,microhardness profile}, title_fa = {بررسی اثر فرآیند فعالسازی مذاب با اعمال کرنش (SIMA) بر ریزساختار و رفتار الکتروشیمیایی آند فداشونده روی در محیط شبیه سازی شده ی آب دریا}, abstract_fa = { روی و آلیاژهای آن به واسطه کاربرد وسیع در سیستم های حفاظت کاتدی به عنوان آندهای فداشونده شناخته شده اند. مشکلات ناشی از فشار بخار بالای این فلز در فرآیند ذوب و ریخته گری، باعث شده که فرآیندهای اصلاح ساختار میکروسکوپی در حالت جامد برای روی بسیار مورد توجه قرار گیرد. فرآیند فعالسازی مذاب با اعمال کرنش (SIMA) یکی از فرآیندهای شکل دهی نیمه جامد در تولید قطعات با ساختار غیردندریتی است. در این پژوهش، اثر فرآیند SIMA بر ریزساختار و رفتار الکتروشیمیایی آند فداشونده ی روی مورد بررسی قرار گرفت. نمونه ها تحت نرخ کرنش های ،%20-50 دماهای مختلف در محدوده ی 425-435°C و زمان های 10-40min قرار گرفتند. ریزساختار بهینه کروی شده در شرایط %50 کارسرد، دمای 430°C و در مدت زمان 10min به دست آمد. نتایج حاصل از آزمون پلاریزاسیون و آزمون آند بر روی نمونه بهینه کروی شده، بیانگر کاهش محسوس %90 چگالی جریان خوردگی الکتروشیمیایی و کاهش اندک بازدهی آند نسبت به نمونه خام است. آنالیز عنصری (EDX) تصاویر متالوگرافی و پروفیل میکروسختی، تجمع عناصر آلیاژی بر روی مرزدانه و تبدیل خوردگی یکنواخت به موضعی و در نتیجه کاهش بازدهی آند بعد از فرآیند SIMAرا نشان می دهد}, keywords_fa = {آند فداشونده روی,فرآیند,SIMA آزمون پلاریزاسیون,آزمون آند,پروفیل میکروسختی}, url = {https://www.jamt.ir/article_70373.html}, eprint = {https://www.jamt.ir/article_70373_70185e1cf728a779d267f29f585141f7.pdf} } @article { author = {Derakhshandeh, Mohammad Reza and Eshraghi, Mohamad Javad}, title = {The Effect of Sintering Process on Electrical and Microstructural Properties of Barium-Strontium-Titanate Sputtering Target and its Thin Film}, journal = {Journal of Advanced Materials and Technologies}, volume = {6}, number = {3}, pages = {79-85}, year = {2017}, publisher = {Materials and Research Center (MERC)}, issn = {2783-0810}, eissn = {2783-0829}, doi = {10.30501/jamt.2017.70374}, abstract = { In this study the effect of sintering parameters on the microstructure and electrical properties of the bariumstrontium titanate sputtering target is investigated. For optimizing the sintering temperature, BST compacts sintered atvarious temperatures ranging from 1200 to 1400 ºC for 2 hours. The sintered Barium Strontium Titanate sputteringtarget comprising with a high density, purity and a fine-grained microstructure has been also fabricated. Optimizedcalcining and sintering condition was obtained by controlling sintering temperature and time to fabricate single phase,high relative density sintered body. A relative density of up to 95% and mean grain size of 8 µm were reached at thesintering temperature of 1250C. The relative permittivity of thin films at 10 KHz was around 4400. Also the thin filmbandgap was around 3.2 eV. The densities of the sintered samples were measured using the Archimedes method.Characteristics of the body were analyzed by X-ray diffraction (XRD), optical microscopy. Dielectric permittivity (εr)were measured with an HP 4192A impedance analyzer and thin film bandgap was analyzed by UV-Vis method. }, keywords = {Barium Strontium Titanate,Sputtering target,Sintering,Solidstate synthesis}, title_fa = {تأثیر فرایند سینتر بر خواص الکتریکی و ریزساختاری تارگت کندوپاش و لایه ی نازک باریوم استرانسیوم تیتانات}, abstract_fa = { در این پژوهش، اثر دمای سینتر بر ریزساختار بدنه های Ba0.5Sr0.5TiO3 و خواص الکتریکی لایه های نازک ایجاد شده به روش کندوپاش مورد بررسـی قرار گرفت. ترکیب سرامیکی Ba0.5Sr0.5TiO3 تک فاز و بدون ناخالصی با استفاده از روش حالت جامد سنتز شد. به منظور بهینه یابی دمای پخـت، ایـن ترکیـب درمحدوده دمای ºC 1200  تا 1400 ºC سینتر شد. نتایج نشان داد که نمونه ی سینترشده در دمای 1250 ºC از %95 چگالی نسبی و میانگین انـدازه دانـه هـای 8 µm برخوردار می باشد که به منظور استفاده برای تارگت کندوپاش مناسب می باشد. گاف انرژی لایه ی نازک اعمال شده از تارگت ساخته شده تحت شـرایط بهینـه eV 3/4 و ثابت دی الکتریک آن در فرکانس 10 kHz برابر با 4400 به دست آمد که نشان دهنده ی خواص مطلوب لایه های نازک این ترکیب از تارگت سـاخته شـده ی آن برای کاربردهای خازنی می باشد. به منظور بررسی های ریزساختاری، فازی و خواص الکتریکی از آزمون های ،XRD میکروسکوپی نوری، اندازه گیـری چگـالی، UV-Vis و اندازه گیری ثابت دی الکتریک استفاده شد  }, keywords_fa = {باریوم استرانسیوم تیتانات,تارگت کندوپاش,سینتر,سنتز حالت جامد}, url = {https://www.jamt.ir/article_70374.html}, eprint = {https://www.jamt.ir/article_70374_e5286aa32539ad53a98aa83abecb851c.pdf} }