@article { author = {Bagheri, R. and Borhani, G.H. and Bakhshi, S.R.}, title = {Study on AA7010 aluminum alloy processed by mechanical alloying}, journal = {Journal of Advanced Materials and Technologies}, volume = {2}, number = {3}, pages = {1-10}, year = {2013}, publisher = {Materials and Research Center (MERC)}, issn = {2783-0810}, eissn = {2783-0829}, doi = {10.30501/jamt.2011.70209}, abstract = {Mechanical alloying is one of advanced methods in producing alloy and composites materials. In this paper, AA7010 alloy was produced from elemental powders through mechanical alloying under argon atmosphere. Particle size measurements showed The results showed that fine and equiaxed particles with mean particle size of 6μm were formed after 28 h milling. The equiaxed particles observed by SEM after mechanical alloying. X-ray diffraction results for milled powders showed that Al crystallite size reduced to 53nm. Different intermetallic compounds including MgZn2, Mg2Zn11, Al2Cu and Al2CuMg were formed in 24 h mechanically alloyed AA7010 powder after annealing treatment at 550 °C in argon atmosphere. The microharness of mechanically alloyed powders was increased with respect to milling time. Differential scanning calorimetry analysis on AA7010 aluminum alloy also indicated that melting point has reduced to 647 °C.}, keywords = {7xxx aluminum alloys,mechanical alloying,XRD}, title_fa = {مطالعه و بررسی آلیاژ آلومینیمAA7010 تولید شده به روش آلیاژسازی مکانیکی}, abstract_fa = {آلیاژسازی مکانیکی یکی از روشهای پرکاربرد در تولید آلیاژها و کامپوزیت های پودری است. در این تحقیق، آلیاژ آلومینیم AA7010 به روش آلیاژسازی مکانیکی و آسیابکاری پودرهای عنصری در یک آسیاب گلوله ای زگواری به مدت 28 ساعت تولید گردید. نتایج نشان داد که میانگین اندازه ذرات پودر آلیاژی AA7010 پس از 28 ساعت آسیابکاری به حدود 6 میکرون رسیده است. تصاویر میکروسکپی الکترونی روبشی (SEM) از پودرهای آسیاب شده نشان داد که پودر آلیاژی AA7010 با ذرات هم محور تولید شده است. آزمون پراش پرتو ایکس(XRD)، کاهش اندازه کریستالیت های آلومینیم را با افزایش زمان آسیابکاری تا 53 نانومتر نشان داد. انجام عملیات حرارتی در دمای C550 و محیط خنثی بر روی پودرهای آلیاژی پس از 24 ساعت آسیابکاری موجب شکل گیری ترکیبات بین فلزی MgZn2، Mg2Zn11، Al2Cu و Al2CuMg شد. آزمون ریزسختی سنجی نشان داد که با ازدیاد زمان آسیابکاری، سختی پودرهای آلیاژی شده افزایش می یابد. همچنین، آغاز فرآیند ذوب شدن پودر آلیاژی AA7010 در دمای C647 به کمک آزمون گرماسنجی روبشی افتراقی (DSC) نشان داد که عملیات آلیاژسازی و کاهش دمای ذوب رخ داده است.}, keywords_fa = {آلیاژهای آلومینیم 7xxx,آلیاژسازی مکانیکی,پراش پرتو ایکس}, url = {https://www.jamt.ir/article_70209.html}, eprint = {https://www.jamt.ir/article_70209_378c9f5e8af59753259d91eb9c0b31d5.pdf} } @article { author = {Alizadeh, Mehdi and Edris, Hossain}, title = {Optimization of fluid flow pattern of molten steel in the steelmaking tundish for clean steel production and optimum intermix amount}, journal = {Journal of Advanced Materials and Technologies}, volume = {2}, number = {3}, pages = {11-23}, year = {2013}, publisher = {Materials and Research Center (MERC)}, issn = {2783-0810}, eissn = {2783-0829}, doi = {10.30501/jamt.2011.70210}, abstract = {Principally, fluid flow pattern in the tundish has important character during the operational conditions such as removing non-metallic inclusions and mixing control. Type of design and geometrical shape of tundish are effective parameters on fluid flow pattern of molten steel in the tundish. In this research, different designing of tundish configuration are considered for achievement to a tundish configuration with optimization of intermix and removing inclusions. With combination of different fluid control devices such as: weir, dam, baffle and turbo stopper, different configuration are suggested for tundish. Furthermore, a mathematical mixing model is designed and free parameters of the model related to each configuration of tundish are determined by a physical model of tundish with one quarter of real scale. Then, residence time distribution curve of each configuration is plotted and characterization of fluid flow pattern is investigated by the mathematical model prediction results. With comparison of RTD curves of different tundish configuration, the best case for fluid flow pattern when is used turbo stopper with a pair of dams as both maximum flotation of inclusions and minimum amount of intermix are evidenced.}, keywords = {Tundish,Intermix,Non-metallic inclusions,Mixing model,Fluid control devices}, title_fa = {بهینه سازی الگوی جریان مذاب در تاندیش فولادسازی به منظور تولید فولاد تمیز و ایجاد حداقل مقدار اختلاط}, abstract_fa = {اساساً شرایط برای حذف بهتر ناخالصی های غیر فلزی و همچنین کنترل اختلاط در تاندیش و کاهش مقدار اختلاط عمدتاً تابع نوع الگوی جریان سیال در تاندیش می باشد. در این رابطه نوع طراحی و شکل هندسی تاندیش از جمله موارد تأثیر گذار بر رفتار جریان مذاب در تاندیش می باشد. در این پژوهش برای دستیابی به یک تاندیش با ایجاد کمترین مقدار اختلاط و امکان بیشترین حذف ناخالصی، طراحی های مختلفی در نظر گرفته شده است. برای این منظور ابتدا با ترکیب سازی وسایل کنترل جریان مانند کاهنده اغتشاش (Turbo Stopper) ، موانع (weir)، سدها(dam) و baffle حالتهای مختلفی برای ساختار داخلی تاندیش پیشنهاد شده است. برای تاندیش مورد نظر یک مدل ریاضی اختلاط طراحی، و پارامترهای آزاد مدل مربوط به هر یک از حالات در نظر گرفته شده، توسط یک سیستم مدل آبی با مقیاس یک-چهارم تاندیش واقعی کالیبره شده است. سپس با رسم منحنی?های توزیع زمان اقامت سیال(RTD) و پیش بینی های حاصل از مدل ریاضی، مشخصه های الگوی جریان سیال برای طرح های مختلف، مورد ارزیابی قرار گرفته است. در نهایت با مقایسه منحنی های RTD مربوط به حالات مختلف، بهترین حالت برای تاندیش با امکان حذف بیشترین ناخالصی و ایجاد کمترین مقدار اختلاط در فولاد مذاب استفاده از کاهنده اغتشاش و یک جفت سد به عنوان یک طرح بهینه پیشنهاد شده است.}, keywords_fa = {اختلاط,تاندیش,ناخالصی های غیرفلزی,مدل ریاضی اختلاط,وسایل کنترل جریان}, url = {https://www.jamt.ir/article_70210.html}, eprint = {https://www.jamt.ir/article_70210_3ccdb27c5cc76bde730527c3d2fdd3c7.pdf} } @article { author = {Ghaderi, Mohammad and monirvaghefi, seyed mahmoud and Saeedi, Ali}, title = {Effect of roughness of the substrate on High-temperature wear behavior of electroless nickel-phosphorus coatings}, journal = {Journal of Advanced Materials and Technologies}, volume = {2}, number = {3}, pages = {24-30}, year = {2013}, publisher = {Materials and Research Center (MERC)}, issn = {2783-0810}, eissn = {2783-0829}, doi = {10.30501/jamt.2011.70217}, abstract = {In this study, electroless coating of nickel-phosphorus on two types of substrates, i.e. sand-blasted and electropolished samples, were applied. Both samples were annealed at 400˚C for one hour in a heat treatment oven. The pin-on-disk wear tests were carried out at 250˚C under normal load of 5N and sliding speed of 0.5 m/s with a sliding distance of 300 m. Morphology and wear behavior of the samples were studied by a scanning electron microscope equipped with energy dispersive X-ray spectroscopy analysis device (EDX). Results indicate that electroless Ni-P coating on the sand blasted substrate is more wear resistance than that on the electropolished substrate, wear type for the former is adhesive and the worn sample of the latter coating contained a lot of micro-cracks.}, keywords = {Electroless Ni-P coating,high temperature wear,sand-blast,electropolish,Hardness,abrasive wear}, title_fa = {بررسی اثر زبری زیرلایه بر رفتار سایش در دمای بالای پوشش الکترولس نیکل-فسفر}, abstract_fa = {در این مطالعه پوشش الکترولس Ni-P بر دو نوع زیرلایه ماسه پاشی شده و الکتروپولیش شده در شرایط یکسان آبکاری شده است. نمونه ها در دمای C˚400 به مدت یک ساعت در کوره تحت عملیات آنیل قرار داده شده است. آزمون سایش در دمای ˚C250 تحت بار اعمالی 10 نیوتن در سرعت m.s-15/0 و مسافت 300 متر به روش پین روی دیسک انجام شدند. بررسی ریخت شناسی و رفتار سایش نمونه ها توسط میکروسکوپ الکترونی روبشی (SEM) به همراه آنالیز طیف سنجی پراش انرژی پرتو اشعه ایکس (EDX) انجام شد. نتایج نشان می دهد سایش در نمونه الکترولس Ni-P با زیرلایه ماسه پاشی شده مقاومت بیشتری دارد و سایش از نوع چسبان می باشد، درحالیکه سایش پوشش با زیرلایه الکتروپولیش با میکروترک?های زیادی در سطح مسیر سایش است.}, keywords_fa = {الکترولس,Ni,P,سایش,دمای بالا,ماسه پاشی,الکتروپولیش,سختی,سایش چسبنده}, url = {https://www.jamt.ir/article_70217.html}, eprint = {https://www.jamt.ir/article_70217_5f13508605c1f9b2aeaef569ff306e72.pdf} } @article { author = {Sohrabi, M. and Hesaraki, Saeed and Kazemzadeh, Ashgar and Alizadeh, Masoud}, title = {The influence of sol-gel processing method on physical properties and acellular in vitro reactivity of bioactive glasses based on CaO-SiO2-P2O5: acidic catalysed single step process versus acid- base two step quick-gelling method}, journal = {Journal of Advanced Materials and Technologies}, volume = {2}, number = {3}, pages = {31-36}, year = {2013}, publisher = {Materials and Research Center (MERC)}, issn = {2783-0810}, eissn = {2783-0829}, doi = {10.30501/jamt.2011.70221}, abstract = {The physical characteristics of the materials such as specific surface area and particles size have great effect on their cellular properties and rate of bone bonding. In this study, bioactive glass based on CaO-SiO2-P2O5 system was produced through sol-gel technique at two different processing method: single step sol-gel route in which precursors are hydrolysis to oxides in an acidic medium and gelation occur at a long period of time and quick alkali-mediated method in which hydrolyzed precursors forms a gel network quickly, due to the use of ammonia solution .Specific surface area and morphology of the glasses were determined by BET and TEM techniques, respectively. For surface reactivity measurements, the powders immersed in simulated body fluid (SBF) for different intervals and then characterized by XRD, FTIR and SEM. The results of TEM and BET measurements showed that both methods provided nano-particles of bioactive glass. The glasses produced through both traditional and quick alkali-mediated methods had approximately the same particle size, but higher specific surface area was obtained for the former (168m2/g) because of its highly porous structure. Precipitation of apatite phase was confirmed on surfaces of glasses though the rate of precipitation was higher for the glass specimen produced by single step process. It seems that the surface reactivity (and hence bone bonding ability) of bioactive glass materials can be controlled using appropriate processing techniques.}, keywords = {bioglass,bone filler,Bioactivity,Sol-Gel}, title_fa = {تاثیرفرآیندسل- ژل اسیدی و اسید-باز برخواص فیزیکی و زیست فعالی شیشه‌های پایهCaO-P2O5-SiO2}, abstract_fa = {خواص فیزیکی شیشه های زیست فعال مانند سطح ویژه و اندازه ذرات تاثیر بسزایی در برهمکنش با سلولها و نرخ ایجاد پیوند شیمیایی با بافت دارد. در این مطالعه شیشه زیست سازگار بر پایه سیستم CaO-SiO2-P2O5 به روش سل- ژل به دو طریق متفاوت تهیه شد. سل- ژل تک مرحله ای، که مواد اولیه طی فرایند هیدرولیز در حضور اسید، اکسایش می یابند و فرآیند ژل شدن در طولانی مدت اتفاق می افتد. روش دوم، روش هیدرولیز مواد اولیه و ژل شدن سریع می باشد که با افزایش pH محیط اسیدی با استفاده از آمونیاک انجام می شود. سطح ویژه و مورفولوژی شیشه ها به وسیله آنالیزهای BET و TEM به دست آمد. برای تعیین واکنش پذیری سطح، پودرها داخل محلول شبیه بدن طی مدت زمان های متفاوت غوطه ور شدند و سپس، به وسیله آنالیزهای XRD و FTIRارزیابی شدند. نتیجه اندازه گیری های BET و TEM نشان داد که در شیشه BG1، ذراتبا اندازه حدود 300 نانومتر و در شیشه BG2 ذرات با اندازه 30-20 نانومتر دیده می شود. شیشه تهیه شده به روش اسید- باز ،ساختار مزومتخلخل به همراه ذرات کوچک تر اما سطح ویژه بالاتر داشت. حجم کل تخلخل ها درBG2/cm3gr 57/0در حالیکه در شیشهBG1، /cm3gr2/0گزارش شده است.رسوب فاز آپاتیت روی سطوح شیشه ها نشان داد که نرخ رسوب در روش اسید-باز بیشتر از روش اسیدی تک مرحله ای می باشد. به نظر می رسد که واکنش پذیری سطوح (و درنتیجه توانایی برقراری پیوند با استخوان) شیشه های زیست فعال رامی توان با بکارگیری روش سنتز مناسب کنترل کرد.}, keywords_fa = {شیشه زیست سازگار,پرکننده استخوان,زیست فعالی,سل- ژل}, url = {https://www.jamt.ir/article_70221.html}, eprint = {https://www.jamt.ir/article_70221_022abdb2f0785d6bc69e192109a7be43.pdf} } @article { author = {Ahmadi, A. and Yuzbashi, A.A. and Shadmehr, A. and Sodagar, L.}, title = {Study of Corrosion in archeological bronze pieces from Luristan province}, journal = {Journal of Advanced Materials and Technologies}, volume = {2}, number = {3}, pages = {37-41}, year = {2013}, publisher = {Materials and Research Center (MERC)}, issn = {2783-0810}, eissn = {2783-0829}, doi = {10.30501/jamt.2011.70222}, abstract = {A study on a metal artifact from Luristan bronzes collection of Reza Abbassi Museum was carried out in order to determine the elemental composition, metallographic data and corrosion products. The sample under study is the head of an axe with a lion shape which looks to be a decoration Piece. The analytical technique used include scanning electron microscopy (SEM) for studing the microstructure, Inductively- coupled plasma (ICP-AES) for major as well as trace elemental analysis, and X-ray diffraction (XRD) for phase analysis. In this paper the results of corrosion study of this Luristan artifact are discussed and the conclusions were drawn accordingly. }, keywords = {bronzes,archeological,corrosion}, title_fa = {بررسی خوردگی یک سر تبر از مجموعه مفرغ های لرستان}, abstract_fa = {یک قطعه فلزی از مجموعه مفرغ های لرستان متعلق به موزه رضا عباسی برای تعیین ترکیب عنصری و متالوگرافی و بررسی خوردگی آن مورد مطالعه قرار گرفت. این قطعه فلزی یک سر تبر دارای نقشی تزئیینی می باشد. این نقش می تواندر حیوانی درنده مانند شیر باشد. برای مطالعات فوق مقداری از محصولات خوردگی از سطح این نمونه جمع آوری گردید و بوسیله دستگاه های آنالیز میکروسکوپ الکترونی جاروبی) (SEM پراش سنجی اشعه ایکس ) (XRD و طیف سنجی نشر اتمی در محیط پلاسمای القایی) (ICP-AES مورد آزمایش و بررسی قرار گرفت. در این مقاله نتایج بدست آمده از مطالعات فوق ترکیب و ساختار مواد موجود در محصولات خوردگی و خاک موجود در آن را شناسایی نمود و بر اساس آنها بحث و بررسی لازم انجام پذیرفت.}, keywords_fa = {مفرغ های لرستان,خوردگی,آنالیز دستگاهی}, url = {https://www.jamt.ir/article_70222.html}, eprint = {https://www.jamt.ir/article_70222_4542a7cd2aba170dd4bea3a7c450dbd3.pdf} } @article { author = {Ghasali, S.E. and Yazdani-rad, R. and Asadian, K. and Ebadzadeh, T.}, title = {The effect of TiC additive on microstructure and final properties of microwave and conventional sintered Al-SiC composite}, journal = {Journal of Advanced Materials and Technologies}, volume = {2}, number = {3}, pages = {42-49}, year = {2013}, publisher = {Materials and Research Center (MERC)}, issn = {2783-0810}, eissn = {2783-0829}, doi = {10.30501/jamt.2011.70223}, abstract = {Al-SiC-TiC composites have been produced via conventional and microwave sintering. The initial composition as: SiC 15 wt%, TiC 1, 3, 5 and 7 wt% and Al balance, were compacted with uniaxial press at 240 MPa. Green samples were subjected to sintering at 650, 750, 850 and 950°C for 1 h and 1 min in a conventional sintering method and a microwave ,respectively. Results indicated that the optimum bending strength corresponded to the sintering at 950°C for samples with 7 wt% and were 140 MPa and 215MPa for conventional and microwave sintered samples, respectively. The microwave sintered specimens showed more uniform distribution of reinforcement particles and higher density than conventional sintered ones concurrent time and energy saving. SEM studies revealed a homogeneous distribution of carbide phases within the Al matrix.}, keywords = {Aluminum,Metal Matrix Composite,Silicon carbide,Titanium Carbide,Microwave sintering}, title_fa = {بررسی تاثیر کاربید تیتانیوم بر‌ریز‌ساختار و خواص نهایی کامپوزیت‌های آلومینیوم-کاربید سیلیسیم تهیه شده به روش‌های حرارت‌دهی معمولی و مایکروویو}, abstract_fa = {در این پژوهش تأثیر افزودنی کاربید تیتانیوم و همچنین پارامترهای سینتر بر ریزساختار و خواص مکانیکی کامپوزیت آلومینیوم- کاربید سیلیسیم مورد مطالعه قرار گرفت. ذرات کاربید تیتانیوم با متوسط اندازه دانه 5 میکرومتر و به میزان 1، 3، 5 و 7 درصد وزنی به کامپوزیت آلومینیوم - 15 درصد وزنی کاربید سیلیسیم اضافه شدند. نمونه های استحکام توسط پرس تک محور در فشار 240 مگاپاسکال پرس و در دماهای 650، 750، 850 و950 درجه سانتیگراد در کوره معمولی به مدت 1 ساعت و کوره مایکروویو به مدت 1 دقیقه در بستر گرافیت سینتر شدند. چگالی نمونه ها به روش ارشمیدس محاسبه و از نمونه ها تست استحکام خمشی گرفته شد و در پایان الگوی پراش پرتو ایکس و مطالعات ریزساختاری توسط میکروسکوپ الکترونی روبشی مورد بررسی قرار گرفت. نتایج نشان می دهد افزودن ذرات کاربید تیتانیوم به میزان 7 درصد وزنی موجب افزایش استحکام خمشی به روش سینتر معمولی و سینتر مایکروویو به میزان 140 و 215 مگاپاسکال به ترتیب، می شود. نمونه های سینتر شده در کوره مایکروویو با توجه به صرفه جویی در زمان و انرژی، ریزساختار همگن تر و چگالی بیشتر را نشان می دهند؛ همچنین مطالعات ریزساختاری نشان دهنده توزیع مناسب ذرات تقویت کننده در زمینه آلومینیوم است.}, keywords_fa = {کامپوزیت‌های آلومینیوم – کاربید سیلیسیم,کاربید تیتانیوم,سینتر مایکروویو}, url = {https://www.jamt.ir/article_70223.html}, eprint = {https://www.jamt.ir/article_70223_c819fcb07596a28d2ae22e0254a35aa7.pdf} } @article { author = {Ghani, Omid . and Heshmat Dehkordi, Ebrahim and yazdanian, S.M.}, title = {Effect of Alloying Elements on Hydrogen diffusion in dissimilar joint of Austenitic stainless steel/Carbon steel}, journal = {Journal of Advanced Materials and Technologies}, volume = {2}, number = {3}, pages = {50-59}, year = {2013}, publisher = {Materials and Research Center (MERC)}, issn = {2783-0810}, eissn = {2783-0829}, doi = {10.30501/jamt.2011.70224}, abstract = {Diffusion of hydrogen in metals and alloys will affect the material behavior such as loss in mechanical properties. In this research the effect of alloying element on the hydrogen diffusion of the cladding AISI 347 with several different chemical compositions has been evaluated. For this purpose a piece of carbon steel St37 was prepared and cladding with filler metal with two different chemical compound 347 stainless steel. In this regard, a non-hazardous electrochemical charging method to hydrogen charge the specimens.. Mechanical properties and microstructure of the specimens were studied by means of micro hardness testing, tensile strength, toughness, optical microscopy and microanalysis techniques (EDS). Results indicate that both overlays were without any defects in the interfaces. Also the results of the cladding samples showed the presence of elements such as Cr, Mn, Ti, Nb can reduce hydrogen permeation and diffusion, while Ni probability can increase permeation and hydrogen embrittlement.}, keywords = {Hydrogen Embrittlement,Dissimilar Metal Welding,Cladding}, title_fa = {بررسی اثر عناصر آلیاژی بر نفوذ هیدروژن در اتصالات غیرمشابه زنگ‌نزن آستنیتی به فولاد کربنی}, abstract_fa = {نفوذ هیدروژن در فلزات و آلیاژها سبب افت خواص مکانیکی آن�ها می�شود. در این پژوهش به بررسی اثر عناصر آلیاژی در روکشAISI 347� با دو ترکیب شیمیایی بر میزان نفوذ هیدروژنی پرداخته شد. بدین منظور نمونه�هایی از جنس فولاد کربنی St37 تهیه شد و سپس توسط فولاد زنگ نزن �با دو ترکیب شیمیائی روکش کاری شده است. سپس نمونه�ها تحت شارژ کاتدی هیدروژن قرارگرفتند و جهت مقایسه با نمونه�های شارژ نشده از آزمون�های فراصوتی، متالوگرافی، سختی�سنجی، طیف سنجی نشر نور، خمش و سنجش ترکیب شیمیائی توسط انرژی پرتو ایکس در میکروسکوپ الکترونی استفاده شد. نتایج بررسی�ها به عمل آمده نشان می�دهد که هر دو روکش فاقد هر گونه عیبی در فصل�مشترک اتصال/زیرلایه می�باشند. یافته�های پژوهش بر نمونه�های روکش نیز نشان داد وجود عناصری مانند کروم، منگنز، تیتانیوم و نایوبیوم می�تواند نفوذ هیدروژن را کاهش دهد، این در حالی است که نیکل احتمال نفوذ و تردی هیدروژنی را در روکش زنگ�نزن آستنیتی افزایش می�دهد.}, keywords_fa = {تردی هیدروژنی,جوشکاری غیرمشابه,روکش‌کاری,عناصر آلیاژی}, url = {https://www.jamt.ir/article_70224.html}, eprint = {} } @article { author = {shams solaree, leila}, title = {Synthesis of Hydrophobic Silica Coatings on Glass by Sol-Gel and Studying Silver Oxide Effect on the Wettability}, journal = {Journal of Advanced Materials and Technologies}, volume = {2}, number = {3}, pages = {60-68}, year = {2013}, publisher = {Materials and Research Center (MERC)}, issn = {2783-0810}, eissn = {2783-0829}, doi = {10.30501/jamt.2011.70225}, abstract = {Wetting behavior of solid surfaces is a key Factor in our daily life as well as in engineering and science. In addition, Control on the wettability of solid state materials is important in surface engineering. Hydrophobic surfaces with water contact angle higher than 90◦ generated a lot of interest both in academia and in industry because of the self-cleaning properties. In present study, TEOS based hydrophobic, self-cleaning silica coatings on a glass substrate by sol–gel process was prepared. The coating sol was prepared by simple dip coating method. The coating alcosol was prepared by keeping the molar ratio of tetraethoxysilane (TEOS), Phenyltriethoxysilan (PTES), ethanol and ammonium hydroxide (NH4OH) constant. The effect of materials such as, silver oxide on hydrophobicity was studied. The films were characterized by scanning electron microscopy (SEM), X-ray powder diffractometry (XRD), Fourier transform infrared spectroscopy (FTIR), water contact angle (CA) and Atomic force Microscopy)AFM( measurements. The results showed that good hydrophobicity is obtained with PTES/TEOS=1 without silver oxide Relative to the sample with silver oxide and the contact angle was 124˚.}, keywords = {Contact angle,Surface hydrophobic,Wetting,Sol-Gel}, title_fa = {سنتز پوشش سیلیسی آبگریز بر روی شیشه به روش سل- ژل و بررسی تاثیر اکسید نقره بر روی تغییرات ترشوندگی آن}, abstract_fa = {رفتار تر شوندگی سطوح جامد یک مساله اساسی در علم و مهندسی و هم در زندگی روزمره به شمار می�رود. علاوه بر این کنترل قابلیت تر شوندگی مواد حالت جامد یک مساله اساسی در مهندسی سطح می باشد. سطوح آبگریز با زاویه تماس بالاتر از ˚90 به دلیل خواص خود تمیز شونده علاقه زیادی را هم در علم و صنعت ایجاد کرده است. در تحقیق حاضر، با استفاده از روش سل-ژل پوشش سیلیسی آبگریز شفاف با پایه تترا اتوکسی سیلان ( TEOS ) بر روی زیر لایه شیشه ایجاد شد و پوشش دهی با استفاده از روش غوطه وری انجام گرفت. برای تهیه سل از TEOS ، اتانول، PTES و هیدروکسید آمونیوم استفاده شد. تاثیر موادی نظیر اکسید نقره بر روی آبگریزی پوشش ایجاد شده مورد بررسی قرار گرفت. ارزیابی پوشش ایجاد شده با استفاده از میکروسکوپ الکترونی روبشی(SEM)، پراش اشعه ایکس (XRD)، طیف سنجی مادون قرمز فوریه(FTIR)، اندازه گیری زاویه تماس(CA) و میکروسکوپ نیروی اتمی (AFM)انجام گرفت. نتایج نشان داد که در نسبت PTES/TEOS=1� آبگریزی �مناسبی در نمونه پوشش داده شده بدون اکسید نقره نسبت به نمونه دارای اکسید نقره می باشد و زاویه تماس برابر با ˚ 124 به دست آمد.}, keywords_fa = {Contact angle,Surface hydrophobic,Wetting,Sol،Gel}, url = {https://www.jamt.ir/article_70225.html}, eprint = {https://www.jamt.ir/article_70225_77b90b3c852abbe537a1a50973de3d01.pdf} } @article { author = {Mohammadi, Fereshteh and Ersahd Langerudi, Amir}, title = {Study of the effect of silica nanoparticles on the conservative properties of acrylic coatings}, journal = {Journal of Advanced Materials and Technologies}, volume = {2}, number = {3}, pages = {69-78}, year = {2013}, publisher = {Materials and Research Center (MERC)}, issn = {2783-0810}, eissn = {2783-0829}, doi = {10.30501/jamt.2011.70226}, abstract = {In this work the properties of acrylic coatings based on Paraloid B72 were improved by adding of silica nanoparticles. Pre-formed silica nanoparticles, prepared by sol-gel chemistry from thetraethoxysilane (TEOS) and methacryloxypropyltrimethoxysilane (MPTMS) precursors, were dispersed into acrylic coatings using a homogenizer. Steel sheets were used as substrate. Morphology and the dispersion of nano-silica particles in the coatings were investigated by scanning electron microscopy (SEM), and transmission electron microscopy (TEM). Topography and surface roughness of the coatings were also evaluated using atomic force microscopy (AFM). The effect of incorporation of silica nanoparticles on the conservative behavior of the coatings was investigated using contact angle measurements and UV aging tests. The modified coating with a proper amount of silica particles showed more efficient performance than the net coating which can be mainly inferenced from its more less color changes after 1000 hr UV radiation and also its more hydrophobic nature than the net coating. In general, the study shows an improvement in the conservative characteristics (from the wet ability and color change point of view) of the properly nano-particle modified coating, confirming the positive effect of nano silica addition in acrylic coatings.}, keywords = {Paraloid,Silica Nanoparticles,Wet ability,Color change}, title_fa = {بررسی اثر افزودن نانو ذرات سیلیکا بر روی خصوصیات حفاظتی پوشش‌های اکریلیکی}, abstract_fa = {در این تحقیق، خصوصیات پوشش�های اکریلیکی بر پایه پارالوئید B72 در اثر افزودن نانو ذرات سیلیکا بهبود یافته است. ورق�های فولادی به عنوان زیرلایه استفاده شده است. نانو ذرات سیلیکا، تهیه شده به روش سل- ژل از پیش ماده�های تترا اتوکسی سیلان (TEOS) و متاکریلوکسی پروپیل تری متوکسی سیلان (MPTMS)، از طریق همزن داخل پوشش اکریلیکی پخش شدند. پوشش�های خالص بدون نانو ذارت نیز برای مقایسه تولید شدند. مورفولوژی و توزیع اندازه ذرات پوشش�ها با استفاده از تکنیک�های میکروسکوپی الکترونی روبشی (SEM) و میکروسکوپی الکترونی عبوری (TEM) بررسی شدند. میکروسکوپ نیروی اتمی (AFM) نیز برای بررسی توپوگرافی و زبری سطح پوشش�ها مورد استفاده واقع شد. اثر افزودن نانو ذرات سیلیکا بر روی خصوصیات محافظتی پوشش�های اکریلیکی با استفاده از آزمون�های ترشوندگی و پیرسازی UV مورد مطالعه قرار گرفت. پوشش اصلاح شده با مقدار بهینه ذرات سیلیکا کارآیی بهتری را در مقایسه با پوشش خالص از خود نشان داد که این امر را می�توان از تغییرات کمتر رنگ آن پس از 1000 ساعت تشعشع UV و همچنین آبگریزتر بودن آن در مقایسه با پوشش خالص استنباط کرد. در مجموع، نتایج حاصل از این تحقیق نشان می�دهند که خصوصیات حفاظتی (از نقطه نظر ترشوندگی و تغییر رنگ) پوشش اصلاح شده با نانو ذرات سیلیکا نسبت به پوشش اکریلیکی خالص بهبود یافته است که این امر تصدیق کننده اثر مثبت افزودن نانو ذرات سیلیکا به زمینه پلیمری بوده است.}, keywords_fa = {پارالوئید,نانو ذرات سیلیکا,ترشوندگی,تغییر رنگ}, url = {https://www.jamt.ir/article_70226.html}, eprint = {https://www.jamt.ir/article_70226_cee4c2b54ec97ec828d70f42a36b7002.pdf} } @article { author = {Kazazi, Mahdi and Vaezi, M.R. and Kazemzadeh, Asghar}, title = {Synthesis, characterization and cyclability of sulfur-polypyrrole composite as a cathode material for lithium secondary batteries}, journal = {Journal of Advanced Materials and Technologies}, volume = {2}, number = {3}, pages = {79-85}, year = {2013}, publisher = {Materials and Research Center (MERC)}, issn = {2783-0810}, eissn = {2783-0829}, doi = {10.30501/jamt.2011.70227}, abstract = {In this research, a sulfur-polypyrrole composite as cathode material of lithium-sulfur batteries was synthesized and evaluated. Polypyrrole conductive polymer was precipitated on the surface of sulfur particles by in-situ polymerization of pyrrole monomer with FeCl3 as the oxidizing agent. The synthesized composite was characterized by Fourier Transform Infrared Spectroscopy, X-ray diffraction, thermogravimetric analysis and scanning electron microscopy. The results of these experiments showed that polypyrrole was synthesized properly on the surface of sulfur particles and no chemical reaction occurred between them. Performance experiments showed that polypyrrole coating leads to increase the specific capacity and columbic efficiency and improve the cyclability of cathode material. A reversible capacity of 502 mAh g-1 was obtained for composite cathode after 50 cycles, which is ~4 times higher thansulfur cathode. The improved performance of the composite cathode is attributed to the enhanced electrical conductivity of cathode material and prevention of “shuttle phenomenon” with addition of polypyrrole.}, keywords = {Lithium-sulfur battery,sulfur-polypyrrole composite,cathode material,cycle performance}, title_fa = {ساخت، مشخصه‌یابی و سیکل‌پذیری ماده کاتدی سولفور- پلی‌پیرول جهت کاربرد در باتری-های ثانویه لیتیمی}, abstract_fa = {در این پژوهش، کامپوزیت سولفور- پلی�پیرول به عنوان ماده کاتدی باتری�های ثانویه لیتیمی ساخته شد و مورد ارزیابی قرار گرفت. پلیمر رسانای پلی�پیرول به روش پلیمریزاسیون درجای مونومرهای پیرول با استفاده از عامل اکسنده کلرید آهن بر سطح ذرات سولفور نشانده شد. مشخصه�یابی کامپوزیت سنتز شده با استفاده از آزمون�های طیف�سنجی تبدیل فوریه مادون قرمز، تفرق اشعه X، توزین حرارتی و میکروسکوپ الکترونی روبشی انجام شد. نتایج این آزمون�ها نشان دادند که پلی�پیرول به درستی بر سطح ذرات سولفور تشکیل شده و هیچ واکنش شیمیایی بین آنها رخ نداده است. آزمون�های عملکردی نشان دادند که پوشش پلی�پیرول سبب افزایش ظرفیت ویژه، افزایش بازده کولنی و بهبود سیکل�پذیری ماده کاتدی می�شود. ظرفیت برگشت�پذیر mAh g-1 502 پس از 50 سیکل برای کاتد کامپوزیتی بدست آمد که حدود 4 برابر ظرفیت کاتد سولفور در همین شرایط می�باشد. بهبود عملکرد کاتد کامپوزیتی به افزایش هدایت الکتریکی ماده کاتدی و جلوگیری از پدیده انتقال با افزودن پلی�پیرول نسبت داده می�شود.}, keywords_fa = {باتری لیتیم,سولفور,کامپوزیت سولفور,پلی‌پیرول,ماده کاتدی,سیکل‌پذیری}, url = {https://www.jamt.ir/article_70227.html}, eprint = {https://www.jamt.ir/article_70227_c281a4051dc64a6090c1790de339df40.pdf} }